Milwaukee M18 3019-21PS handleiding
Handleiding
Je bekijkt pagina 7 van 24
7
APPLICATIONS
WARNING
Before using any chemicals and/
or solutions, read and follow all
original manufacturer instructions. Read all
Safety Data Sheets (SDS) and container labels
provided with the chemical. Chemicals can cause
serious bodily injury, property damage, and/or
damage the tool. Wear personal protective equip-
ment (PPE) according to the chemical manufac-
turer's instructions. Always wear eye protection.
Spraying
(Cat. No. 49-16-19PS)
1. Fill the tank and then install onto the base.
2. Put on the backpack and properly adjust the
straps.
3. Turn on the tool.
4. Pull the trigger and begin sweeping the nozzle
from side to side, coating the desired surface
evenly in accordance with chemical manufac-
turer's instructions.
5. If desired, lock-on the trigger for extended use.
6. When done, release the trigger, turn o the tool,
remove the backpack, drain, and clean the tank.
Supplying Water
(Cat. No. 49-16-19WS)
1. Fill the tank with clean water and then install onto
the base.
2. Place tool near the job within range of water sup-
ply hose.
3. Attach water supply hose with the quick connect
tting. Pull on the connection to be certain it is
properly secured.
4. To start water ow, turn on the tool.
5. Monitor water level in tank. When empty, turn o
tool, disconnect the hose, and rell tank. Don't run
tool when tank is empty.
6. When done, turn o the tool, disconnect hose,
drain, and clean the tank.
Adjusting the Flow Rate
Select the desired ow rate from Low (1) to High (5),
depending on the job and the chemical manufac-
turer's instructions.
Flow
Rate
3019-20PS
(Stream Nozzle)
3019-20WS
(Open Flow)
1 0.10 GPM 0.13 GPM
2 0.20 GPM 0.30 GPM
3 0.32 GPM 0.52 GPM
4 0.45 GPM 0.77 GPM
5 0.60 GPM 1.26 GPM
WARNING
To reduce the risk of injury, al-
ways wear personal protective
equipment (PPE) according to the chemical
manufacturer's instructions. Always wear eye
protection.
Always ensure battery compartment latch is
securely closed before use.
Ensure trigger handle lock-on is not engaged
before turning ON tool.
Turning the Pesticide Sprayer ON/OFF
(Cat. No. 49-16-19PS)
1. Install the battery pack. Close and latch the battery
compartment.
2. To turn the sprayer ON, press the ON/OFF switch
to "I". The power LED will light green.
3. To start the ow of liquid at the spray wand, pull
the trigger.
4. To stop the ow of liquid at the spray wand, re-
lease the trigger.
5. To turn the sprayer OFF, press the ON/OFF
switch to "O".
NOTE: Be aware some spray material may remain
inside the spray wand and drip out. To drain, turn o
the tool, then pull the trigger and point the tool down
until dripping stops.
Turning the Water Supply ON/OFF
(Cat. No. 49-16-19WS)
1. Install the battery pack. Close and latch the battery
compartment.
2. To turn the water supply ON, press the ON/OFF
switch to "I". The power LED will light green.
NOTE: If the maximum pressure is reached, the
pump will cut o until the pressure drops and the
motor will start running again.
3. To turn the water supply OFF, press the ON/OFF
switch to "O".
NOTE: Be aware some water may remain inside
the hose and drip out. To drain, turn o the tool,
then twist the nozzle and point the tool down until
dripping stops.
Bekijk gratis de handleiding van Milwaukee M18 3019-21PS, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Milwaukee |
| Model | M18 3019-21PS |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 4434 MB |
