Metabo RW 18 LTX BL 120 handleiding
Handleiding
Je bekijkt pagina 11 van 76
ENGLISH en
11
7.1 Tool change
Attaching the agitator paddle:
Screw the agitator paddle into the spindle (1). Hold
the spindle (1) using an open-ended wrench and fix
the agitator paddle using a second open-ended
wrench.
Note: If needed screw in the supplied extension
piece.
Remove the tool:
Hold the spindle (1) using an open-ended wrench
and remove the agitator paddle using a second
open-ended wrench.
7.2 Select the gear (depending on features)
Select the required gear by rotating the thumb
wheel (2).
Change speed when the motor is at a standstill or
the machine is in the process of running down
(briefly switch it on and off).
I = 1. gear
(low speed, high torque)
II = 2. gear
(high speed)
7.3 Adjusting the max. speed (depending on
features)
Pre-select the maximum speed on the setting wheel
(5) and change while working if needed.
Speed table, see page 3.
7.4 Switching On and Off
Changing the speed
Always hold the machine with both hands on
the designated handles, take a secure stance
and concentrate on the work.
Switching on, changing the speed: Press the
trigger lock (4) and keep pressed, then press the
trigger switch (3). Release the locking button (4).
Press in the trigger switch to increase the rotational
speed.
To switch off release the trigger switch (3).
Continuous operation (not for RWE 1200):
RWEV 1200-2, RWEV 1600-2, RW 18 LTX BL
120: When set to continuous operation, the
machine will keep running even if it is snatched from
the hand.
Switch on the machine and with the trigger (3)
pressed, push in the locking button (4) completely
and then released the trigger (3). Release the
locking button (4).
Press and release the trigger (3) again to switch off.
Clean the agitator paddle after each use.
Clean the machine regularly.
9.1 Mains powered machines:
There is a MAJOR reduction in load speed:
Overload protection:
The motor temperature is too high! Allow the
machine to run at idle speed until it has cooled
down. Use an agitator paddle suited for the
application. For RWEV...: set first gear
There is a MINOR reduction in load speed:
Overload protection:
The machine is overloaded. Reduce the load before
continuing to work. Use an agitator paddle suited for
the application. For RWEV...: set first gear
The machine does not start:
Restart protection
Restart protection is active. If the mains plug is
inserted with the machine switched on or if the
power supply is restored following an interruption,
the machine does not start up. Switch the machine
off and back on again.
9.2 Cordless machines:
1 x beep, the machine does not start:
Restart protection
Restart protection is active. The machine will not
start if the battery pack is inserted while the machine
is on. Switch the machine off and back on again.
2 x beep, the machine was switched off
automatically:
Overload protection:
The machine is overloaded. Reduce the load before
continuing to work. For RW 18 LTX BL 140-2: set
first gear Use an agitator paddle suited for the
application. If the machine is too warm: let run in idle
until the machine has cooled down.
3 x beep, the machine was switched off
automatically when set to continuous
operation (Only for RW 18 LTX BL 140-2):
Safety stop.
For safe and clean working: Quick stop in the event
of jamming or loss of control. Grasp the machine
firmly with both hands on the designated handles,
switch it off and then back on, and proceed with
normal operation.
ENG
Use only original Metabo or CAS (Cordless Alliance
System) battery packs and accessories.
7. Use
8. Cleaning
9. Troubleshooting
10. Accessories
Bekijk gratis de handleiding van Metabo RW 18 LTX BL 120, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Metabo |
| Model | RW 18 LTX BL 120 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 10217 MB |
