MBM BR773P handleiding
Handleiding
Je bekijkt pagina 7 van 12
A010044 Rev. 1 Pagina 7 di 12
The electrical safety of this equipment is only assured when the above-mentioned conditions are met and if the systems equipotential
situation is also in order (use the connection screw located near the power cable entry and the
label featuring the symbol)
NOTE: Because this appliance has a Y-type electric connection, the power supply cable must only be replaced by a
qualified electrician.
The Manufacturer declines all liability for situations arising from failure to comply with these safety regulations.
7. OPERATION / USE
7.1
Operating tips
• Avoid placing hot foods or evaporating liquids inside the unit.
• Cover or wrap foods to be kept inside.
• Only keep the doors open for as long as it takes to put the food inside or take it out.
• Leave the space around the exchangers clear to enable sufficient circulation of the air.
• Before using the equipment for the first time, clean it inside with lukewarm water and neutral soap. Avoid using abrasive detergents
or scouring powders. Lastly, rinse and dry thoroughly.
7.2
Starting up
• Turn on the circuit breaker located upstream from the equipment.
• Switch on the digital thermostat A of Fig.1 by pressing the buttom 4 for at least 5” time (see picture)
• If the temperature in the refrigerated unit is higher than the thermostat value, the compressor starts working and the thermostat’s
LED 6 comes on.
7.3 Digital thermostat
Key
1 – Display
2 – “Increase value” push button, activates manual defrost
3 – “Decrease value” push button, manual alarm reset
4 – Press at least 5” to activate the stand-by function - “Exit function” push button
5 – “Access set point push button, accesses menus, confirms commands, displays alarms
6 – Red LED on, compressor running
7 – Red LED on, defrost in progress
8 – Red LED on, alarm active, flashing when alarm silenced
During normal operation, the instrument displays the temperature measured in the refrigerated area.
To display the current set point (selected temperature), press and release the key set, the message "set will appear, press again the
key set.
To modify the working set point, press and release the key set, the message "set will appear, press again the key set, the set value
appears, to modify it within 15 seconds use the push buttons ▲(2) or ▼(3) to increase or decrease the value; after modification, to
memorize, again press the key set.
The set point can be given any of the values within the established minimum and maximum temperature
DEFROSTING can be activated at any time by pressing the ▲ key for at least 4 seconds. Automatic defrosting starts from this moment
after the defrosting interval, factory set at 6 hours and lasts 15 minutes.
WARNINGS AND ALARMS
‘E1’ on the display indicates that the thermostat probe is faulty indicating one of the following anomalies: incorrect type of basin
probe, defective probe, defective connections; check the condition of the probe and correct connection between instrument and probe.
“AH1” high temperature alarm on display indicates that the reading value is higher then the presetted max. value; it causes no effect
to the regulation, the alarm stops when the temperature decreases under the presetted max. value.
“AL1” low temperature alarm on display indicates that the reading value is lower then the presetted minimum value, it causes no
effect to the regulation, the alarm stops when the temperatures rises over the presetted minimum value.
The editing of the thermostat’s CONFIGURATION PARAMETERS, which are factory set, must be performed by qualified personnel
only according to the instructions attached.
7.4 Total switch-off
When the unit is to be mothballed for a lengthy period, the following measures must be taken:
• Switch off the unit with the master switch.
• Disconnect the power supply upstream.
• Remove all the food from the cooler and basin and clean the inside as well as all the accessories.
• Leave the doors ajar so that fresh air can get inside, preventing undesirable smells from forming.
• Protect the stainless steel surfaces by smearing them with Vaseline oil: use a cloth soaked in the oil and rub vigorously.
• Air the room periodically.
GB
Bekijk gratis de handleiding van MBM BR773P, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | MBM |
| Model | BR773P |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 1108 MB |
