Makita HS013G handleiding
Handleiding
Je bekijkt pagina 19 van 132
19 ENGLISH
State of abnormality Probable cause (malfunction) Remedy
The vacuum cleaner does not run
along with the switch operation of
the tool.
The wireless unit is not installed into
the tool.
Thewirelessunitisimproperlyinstalled
into the tool.
Installthewirelessunitcorrectly.
The terminal of the wireless unit and/or
theslotisdirty.
Gentlywipeodustanddirtontheterminalofthe
wireless unit and clean the slot.
The wireless activation button on the
tool has not been pushed.
Pushthewirelessactivationbuttonbrieyandmake
sure that the wireless activation lamp is blinking
in blue.
Thestand-byswitchonthevacuum
cleaner is not set to "AUTO".
Setthestand-byswitchonthevacuumcleanerto
"AUTO".
More than 10 tools are registered to the
vacuum cleaner.
Perform the tool registration again.
If more than 10 tools are registered to the vacuum
cleaner, the tool registered earliest will be cancelled
automatically.
The vacuum cleaner erased all tool
registrations.
Perform the tool registration again.
Nopowersupply Supplythepowertothetoolandthevacuum
cleaner.
Thetoolandvacuumcleanerareaway
fromeachother(outofthetransmission
range).
Get the tool and vacuum cleaner closer each other.
The maximum transmission distance is approxi-
mately10mhoweveritmayvaryaccordingtothe
circumstances.
Radiodisturbancebyotherappliances
whichgeneratehigh-intensityradio
waves.
Keepthetoolandvacuumcleanerawayfromthe
appliances such as Wi-Fi devices and microwave
ovens.
The vacuum cleaner runs while the
tool is not operating.
Other users are using the wireless
activation of the vacuum cleaner with
their tools.
Turnothewirelessactivationbuttonoftheother
tools or cancel the tool registration of the other
tools.
MAINTENANCE
CAUTION: Always be sure that the tool is
switched o and the battery cartridge is removed
before attempting to perform inspection or
maintenance.
CAUTION: Clean out the upper and lower
blade guards to ensure there is no accumulated
sawdust which may impede the operation of the
lower blade guarding system.Adirtyguardingsys-
temmaylimittheproperoperationwhichcouldresult
inseriouspersonalinjury.Themosteectivewayto
accomplish this cleaning is with compressed air. If
the dust is being blown out of the blade guards,
be sure the proper eye and breathing protection
is used.
CAUTION: After each use, wipe o the saw
dust on the tool.Finesawdustmaycomeinsidethe
toolandcausemalfunctionorare.
NOTICE: Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
To maintain product SAFETY and RELIABILITY,
repairs,anyothermaintenanceoradjustmentshould
beperformedbyMakitaAuthorizedorFactoryService
Centers,alwaysusingMakitareplacementparts.
Adjusting 0°-cut accuracy
NOTICE: Before starting the setting, make sure
the lock of the cutting depth is rmly secured.
Thisadjustmenthasbeenmadeatthefactory.Butifitis
o,youcanadjustitasthefollowingprocedure.
1. Loosen the bevel angle lock so that the bevel
angle can be changed.
NOTE: Refer to the section about bevel cutting for
how to tighten or loosen the bevel angle lock.
2. Put a triangular rule or square rule onto the side of
circular saw blade and the base.
While keeping the side of circular saw blade and the
baseperpendicular,turntheadjustingscrewtomake
0° position.
►Fig.37: 1. Triangular rule 2.Adjustingscrew
3. Lock the bevel angle and make a test cut to check
the verticalness.
Bekijk gratis de handleiding van Makita HS013G, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Makita |
| Model | HS013G |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 20278 MB |
