Makita DBN610 handleiding
Handleiding
Je bekijkt pagina 13 van 92
13 ENGLISH
CAUTION: When installing the hook, always
secure it with the screw rmly. If not, the hook
may come o from the tool and result in the personal
injury.
CAUTION: Use the hanging/mounting parts
for their intended purposes only. Using for unin-
tended purpose may cause accident or personal
injury.
CAUTION: Make sure to hang the tool
securely before releasing your hold. Insucient
or unbalanced hooking may cause falling o and you
may be injured.
The hook is convenient for temporarily hanging the
tool. Hang the tool on a tool rack, rail or the wall with
the hook.
The hook can be installed on either side of the tool.
To install the hook, insert it into a groove in the tool
housing on either side and then secure it with the screw
as shown in the gure. To remove, loosen the screw
and then remove the hook.
► Fig.16: 1. Groove 2. Hook 3. Screw
OPERATION
Testing safety system
WARNING: Make sure all safety systems are
in working order before operation. Failure to do
so may cause personal injuries.
► Fig.17: 1. Switch trigger 2. Contact element
3. Magazine 4. Pusher
Test safety system as follows for possible fault or mal-
function before operation.
1. Remove the battery cartridge from the tool. Then
unload all the fasteners left in the magazine.
2. Install the battery cartridge in place and turn the
tool on.
3. Pull the switch trigger without placing the contact
element against the material.
4. Pull the pusher downward and hold it in place.
Then place the contact element against the material
without pulling the switch trigger.
If the tool works in case step 3 or 4 described above,
safety system is not functioning properly. Stop using
the tool immediately and ask your local Makita Service
Center.
Handling of the fasteners
Nails
Handle nails and their box carefully. If the nails have
been handled roughly, they may be out of shape or their
connector breaks, causing poor nail feed.
NOTICE: Avoid storing nails in a very humid or
hot place or place exposed to direct sunlight.
► Fig.18
Driving fasteners
WARNING: Keep your face away from the tool
when operating the tool. Failure to do so may cause
injury.
WARNING: Do not use this tool for fastening
electrical cables. This tool is not designed for elec-
tric cable installation and may damage the insulation
of electric cables thereby causing electric shock or
re hazards.
WARNING: Continue to place the contact
element rmly on the material until the fastener
is driven completely. Unintentional ring may cause
personal injuries.
CAUTION: Hold the tool rmly during
operation.
CAUTION: Do not drive fasteners on hard
materials such as metal or the like. If the fastener
cannot penetrate the material, the tool may be kicked
back toward you and injury result.
NOTICE: The tool will not start fastening after
ve seconds no switch operation while either
the switch trigger or the contact element is being
solely actuated. Release the switch trigger or
pull the contact element free from the workpiece,
and then reposition the tool in place to restart
fastening.
NOTE: If you drive fasteners continuously for a long
time, the exhaust air will get hot due to the heat from
the motor.
The tool employs two driving actions; full sequential
actuation and contact actuation.
NOTE: Only a single driving mode (full sequential
actuation) is available in some regions or countries.
The switch design varies depending on your region
of residence.
Full sequential actuation
In this mode, you can drive one fastener by one
sequential operation.
A workpiece contact and then a trigger need to be
activated in a specic sequence to actuate the tool.
Release and re-activate the switch controls in the same
sequence to continue driving fasteners.
1. Press and hold the main power button to turn on
the tool.
2. Make sure that the sequential actuation mode
lamp lights up.
► Fig.19: 1. Main power button 2. Sequential actua-
tion mode lamp
3. Place the contact element at on the material.
► Fig.20: 1. Contact element
4. Pull the switch trigger fully to drive a fastener.
► Fig.21: 1. Switch trigger
Bekijk gratis de handleiding van Makita DBN610, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Makita |
| Model | DBN610 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 14247 MB |
