Makita DBN610 handleiding
Handleiding
Je bekijkt pagina 12 van 92
12 ENGLISH
Lighting up the lamp
CAUTION: Do not look in the light or see the
source of light directly.
Pull the switch trigger or actuate the contact element to
light up the lamp. The lamp keeps on lighting while pull-
ing the switch trigger or actuating the contact element.
The lamp goes out several seconds after releasing the
switch trigger and the contact element.
► Fig.8: 1. Switch trigger 2. Contact element 3. Lamp
NOTICE: Use a dry cloth to wipe the dirt o the
lens of the lamp. Be careful not to scratch the lens
of lamp, or it may lower the illumination.
NOTICE: When the tool is overheated, the lamp
ashes. In this case, release the switch trigger
and contact element, and then cool down the tool/
battery before operating again.
NOTE: The tool may not re after the battery
becomes low on power even while the lamp remains
lit. In this case, charge the battery cartridge.
ASSEMBLY
CAUTION: Always be sure that the tool is
switched o and the battery cartridge is removed
before carrying out any work on the tool.
Loading/unloading the fasteners
CAUTION: Always make sure that the battery
cartridge is removed before loading the fasteners.
Unintentional ring may cause personal injuries and
property damage.
CAUTION: Be careful not to get your ngers
caught in the magazine. The pusher tends to
spring back to its original position when the pusher is
unlocked.
CAUTION: Do not abruptly slide the pusher
with fasteners loaded in the magazine. Accidentally
dropping fasteners especially when working in high
places may cause personal injuries.
CAUTION: Load the fasteners in the correct
direction. Loading in wrong direction may cause
premature wear and tear of the driver and damage of
the other parts.
NOTICE: Gently slide the pusher along the mag-
azine. A forceful contact between the pusher and
fastener strip may damage the fasteners.
NOTICE: Make sure that the fastener strip is
properly aligned in the magazine and secured
with the pusher. If not, try reloading.
NOTICE: Do not use deformed fasteners and
fastener strips. Use fasteners specied in this
manual. Using fasteners other than those specied
may cause fastener jamming and malfunction.
1. Remove the battery cartridge.
2. Pull the pusher downward until it locks with a little
click.
► Fig.9: 1. Pusher
3. Insert the fastener strip into the slit on the bottom
of the magazine.
► Fig.10: 1. Slit 2. Fastener strip 3. Magazine
4. Pull and hold the pusher downward and then
press the "A" portion as shown in the gure.
The pusher is unlocked and holds the fasteners in the
magazine.
► Fig.11: 1. Pusher
To remove the fasteners, pull the pusher downward until
it locks with a little click. Take out fasteners from the slit
on the bottom of the magazine.
Nose adapter
CAUTION: Always make sure that your n-
gers are not placed on the switch trigger or the
contact element, remove all the fasteners left in
the magazine, and remove the battery cartridge
before attaching or detaching the nose adapter.
When driving fasteners on the material with easi-
ly-marred surfaces, attach the nose adapter onto the
contact element.
Attaching nose adapter
Put the nose adapter on the contact element. Make
sure that the nose adapter ts perfectly as illustrated.
► Fig.12: 1. Nose adapter 2. Contact element
Detaching nose adapter
The nose adapter can be removed by hand.
NOTE: When you cannot remove the nose adapter
by hand, insert the slotted screwdriver between the
nose adapter and contact element and remove the
nose adapter.
► Fig.13: 1. Nose adapter 2. Contact element
3. Slotted screwdriver
NOTE: You can store the nose adapter on the holder
as shown in the gure to keep it from being lost.
► Fig.14: 1. Nose adapter 2. Holder
Hook
WARNING: Be careful not to overload the
hook as too much force. Otherwise irregular over-
burden may cause damages to the tool resulting in
personal injury.
CAUTION: Do not hang the hook from the
waist belt. Dropping the tool, which is caused by the
hook accidentally coming out of place, may cause
unintentional ring and result in personal injuries.
► Fig.15
Bekijk gratis de handleiding van Makita DBN610, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Makita |
| Model | DBN610 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 14247 MB |
