Lofrans SX3 handleiding
Handleiding
Je bekijkt pagina 14 van 22
14
SX3
Problem Possible causes Solution
8. The shaft does
not run well, is not
aligned, and so is
the gypsy and/or
the bell.
8.1 The shaft bent because the winch
was subjected to an excessive
load.
8.1 Check out that the procedures of use fall within the
specications of the winch. (SERVICE) Uninstall the winch
and replace the shaft. Take this opportunity to replace worn
parts, gaskets, seeger, tabs and oil.
9. Loss of oil between
the engine and the
gearbox body
9.1 The coupling of the engine is
loose and causes the worm screw
into an irregular rotation, leading
to loss of oil from the gasket.
9.1 (SERVICE) Find the reasons why the screws or nuts have
become loose. Uninstall the engine and check out the status
of the spindle and the hole of the worm screw. If an oval
form of the cylindrical part of the screw is observed (outer
hole and diameter) uninstall the winch and repair the dam-
aged parts on the bench. Check out if the oil has entered
into the electrical engine. Take this opportunity to replace all
gaskets, tabs, seeger, screws, oil, and any worn parts.
10. On installation, it is
found that the shaft
and the studs are
short for a correct
coupling with the
gearbox.
10.1 The request referred to the deck
thickness was wrong.
10.1 If the key shaft works in the gearbox along all its length, the
xing studs can be adapted. Otherwise, a longer shaft must
be requested.
11. The winch runs
slowly and at times
jumps the circuit
breaker.
11.1 Section of cables not suitable.
11.2 Poor electrical connections.
11.3 Dirty brushes.
11.4 Water leaks in the electrical
engine.
11.5 There is no parallelism between
upper deck and below deck.
11.6 The gearbox has lost oil.
11.7 The engine strains in one or both
directions.
11.8 The winch works only in one
direction.
11.1 Increase the cable section
11.2 Check out the connections
11.3 Clean the brushes
11.4 Replace the electrical engine
11.5 Work surfaces and/or add shims to restore parallelism.
11.6 (SERVICE) Uninstall the gearbox and check out its condi-
tion. Replace damaged parts after discovering the causes
of the leak. Also, replace gaskets and screws. Check out
also the engine condition, which may have been damaged
during the malfunction.
11.7 (SERVICE) Check out appropriately all connections of
the power cables. If they are alright, uninstall the engine
(in some cases it is convenient to disassemble also the
gearbox). Check out and possibly replace the brushes.
11.8 Check out on the control box that between B2-C and B3-C
contacts there are 12/24V when the respective buttons are
pressed. If this should happen and one of the relays does
not work, replace the control box.
12. The nger is
broken
12.1 Poor layout of the cable top or
rolling of the chain has broken
the nger. Check out the suita-
bility of the gypsy to work with
the nger.
12.1 Replace the nger.
12.2 In the event that the gypsy cannot work properly with the
nger, position the replacement kit (cap).
Lofrans'
Bekijk gratis de handleiding van Lofrans SX3, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Lofrans |
| Model | SX3 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 3215 MB |
