Lofrans SX2 handleiding
Handleiding
Je bekijkt pagina 12 van 20
12
SX2
Problem Possible causes Solution
4. The electric engine
runs but the shaft
does not rotate
either Up or Down
4.1 Heavy wear or breakage of
teeth of the crown / worm
screw.
4.2 Breakage of the engine
spindle.
4.1 (SERVICE) Uninstall the winch and replace the broken parts.
Check out carefully that pieces or splinters of broken parts did
not enter into the oil circuit and have ruined other mechanical
parts. (*)
4.2 (SERVICE) Replacing of the engine. Care must be taken that
the broken part did not remain in the hole of the worm screw. (*)
(*) Take advantage of this opportunity to replace any other worn
parts, especially gaskets, screws, tabs, seeger, and oil.
5. The electric engine
runs, the shaft
rotates Up, but does
not rotate Down
5.1 The chain locker is tangled;
therefore, the emergency
mechanism becomes
operative.
5.2 The chain is of poor quality
with burrs and zinc deposits
that do not allow the free
ow of the links; therefore,
the emergency mechanism
becomes operative.
5.3 The chain was placed in the
locker in block and the links
are stuck with each other;
therefore, the emergency
mechanism becomes
operative.
5.4 Wear of the emergency
mechanism of the spring
control.
5.5 The chain stripper interferes
with the gypsy: it is possible
to weigh the operation, while
to lower, the emergency
mechanism becomes
operative.
5.1 Check out that immediately after the anchor there is a joint that
allows the chain to unfold properly when weighed.
5.2 Remove the chain from the locker and inspect it link by link.
Intervene with the appropriate tools to make it as loose as
possible and free of obstructions.
5.3 Lower manually all the chain in a sea bed deep enough to
enable it to unfold properly. Retrieve it with the winch.
5.4 A (SERVICE) Uninstall the winch from the boat and disassemble
it into its parts by replacing the spring. Take advantage of this
opportunity to replace any other worn parts, gaskets, screws,
tabs, seeger, and oil.
B (SERVICE) It is possible to block the EMERGENCY
MECHANISM so that the gears are always engaged
both in UP and in Down. This operation must be
authorized by the shipowner. The solution rules out completely
the possibility of carrying out the
emergency operation.
5.5 Restore the condition of the chain stripper by repositioning
properly in the gypsy centreline. If it is deformed. It must be
replaced.
6. The electric engine
runs but it cannot be
bell warped.
6.1 The bell warp is being used
wrongly; therefore, the emer-
gency mechanism becomes
operative
6.1 To carry out the warping operation the main shaft must run in
the same rotation direction of the winch gypsy when it weighs
the chain.
7. The winch cannot
be weighed: the
electric engine runs,
the shaft runs, but
the gypsy is still
7.1 The gypsy is not closed on the
clutch cones and slips under
the load effect, or for some
reason the closing wheel is
at end stroke. Check out all
pieces in sequence.
7.2 The clutch cones or the gypsy
cones are deformed and the
clutch hubs are in contact and
prevent closure.
7.1 Check out clutch tightening. If necessary, measure the parts
and check out possible deformations. It is possible to add some
thickness to stem the problem. Then replace the damaged parts.
7.2 Replace the clutch and/or the gypsy
Lofrans'
Bekijk gratis de handleiding van Lofrans SX2, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Lofrans |
| Model | SX2 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 3068 MB |
