Lofrans SX1 handleiding
Handleiding
Je bekijkt pagina 12 van 20
12
SX1
Problem Possible causes Solution
4. The electric engine
runs but the shaft does
not rotate either Up or
Down
4.1 Heavy wear or breakage of teeth
of the crown / worm screw.
4.2 Breakage of the engine spindle.
4.1 (SERVICE) Uninstall the winch and replace the broken
parts. Check out carefully that pieces or splinters of broken
parts did not enter into the oil circuit and have ruined other
mechanical parts. (*)
4.2 (SERVICE) Replacing of the engine. Care must be taken
that the broken part did not remain in the hole of the worm
screw. (*)
(*) Take advantage of this opportunity to replace any other worn
parts, especially gaskets, screws, tabs, seeger, and oil.
5. The electric engine
runs, the shaft rotates
Up, but does not rotate
Down
5.1 The chain locker is tangled;
5.2 The chain is of poor quality with
burrs and zinc deposits that do
not allow the free ow of the links;
5.3 The chain was placed in the locker
in block and the links are
stuck with each other;
5.1 Check out that immediately after the anchor there is a joint
that allows the chain to unfold properly when weighed.
5.2 Remove the chain from the locker and inspect it link by
link. Intervene with the appropriate tools to make it as loose as
possible and free of obstructions.
5.3 Lower manually all the chain in a sea bed deep enough to
enable it to unfold properly. Retrieve it with the winch.
6. The winch cannot be
weighed: the electric
engine runs, the shaft
runs, but the gypsy
is still
6.1 The gypsy is not closed on the
clutch cones and slips under the load
effect, or for some reason the closing
wheel is at end stroke. Check out all
pieces in sequence.
6.2 The clutch cones or the gypsy
cones are deformed and the clutch
hubs are in contact and prevent
closure.
6.1 Check out clutch tightening. If necessary, measure the parts
and check out possible deformations. It is possible to add some
thickness to stem the problem. Then replace the damaged parts.
6.2 Replace the clutch and/or the gypsy
7. The shaft does not
run well, is not aligned,
and so is the gypsy
and/or the bell.
7.1 The shaft bent because the winch
was subjected to an excessive load.
7.1 Check out that the procedures of use fall within the speci-
cations of the winch. (SERVICE) Uninstall the winch and replace
the shaft. Take this opportunity to replace worn parts, gaskets,
seeger, tabs and oil.
8. Loss of oil between
the engine and the
gearbox body
8.1 The coupling of the engine is
loose and causes the worm screw into
an irregular rotation, leading to loss of
oil from the gasket.
8.1 (SERVICE) Find the reasons why the screws or nuts have
become loose. Uninstall the engine and check out the status
of the spindle and the hole of the worm screw. If an oval form
of the cylindrical part of the screw is observed (outer hole and
diameter) uninstall the winch and repair the damaged parts on
the bench. Check out if the oil has entered into the electrical
engine. Take this opportunity to replace all gaskets, tabs,
seeger, screws, oil, and any worn parts.
9. On installation, it is
found that the shaft
and the studs are short
for a correct coupling
with the gearbox.
9.1 The request referred to the deck
thickness was wrong.
9.1 If the key shaft works in the gearbox along all its length, the
xing studs can be adapted. Otherwise, a longer shaft must be
requested.
Lofrans'
Bekijk gratis de handleiding van Lofrans SX1, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Lofrans |
| Model | SX1 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 2954 MB |
