Lofrans SX1 handleiding
Handleiding
Je bekijkt pagina 11 van 20
11
www.lofrans.com
Problem Possible causes Solution
1. The anchor
windlass does not
work when a control is
operated
1.1 Protection switch in OFF
position
1.2 Lack of voltage in the system
1.3 Failure of the control box
1.4 Failure of the control
1.5 Failure of the electric motor
1.1 Check the protection switch and set it in the ON position
1.2 Check the charge status of the battery, check connections
1.3 Check and possibly replace the control box
1.4 Check and possibly replace the control
1.5 Measure the electric motor voltage; if it is OK, check the brushes
and clean them. If it does not work, replace the electric motor
2. The chain jams
frequently
2.1 The chain locker is not deep
enough with respect to the
quantity of chain chosen
2.2 The chain is not suitable for
the gipsy
2.3 The chain is not calibrated
2.1 Position the anchor windlass in the deepest point of the chain
locker or reduce the quantity of chain
2.2 Change the gipsy
2.3 Check the chain: if it does not meet the tolerances, it must be
replaced
3. The winch runs
slowly and at times
jumps the circuit
breaker.
3.1 Section of cables not suitable.
3.2 Poor electrical connections.
3.3 Dirty brushes.
3.4 Water leaks in the electrical
engine.
3.5 There is no parallelism be-
tween upper deck and below deck.
3.6 The gearbox has lost oil.
3.7 The engine strains in one or
both directions.
3.8 The winch works only in one
direction.
3.1 Increase the cable section
3.2 Check out the connections
3.3 Clean the brushes
3.4 Replace the electrical engine
3.5 Work surfaces and/or add shims to restore parallelism.
3.6 (SERVICE) Uninstall the gearbox and check out its condition.
Replace damaged parts after discovering the causes of the leak.
Also, replace gaskets and screws. Check out also the engine condi-
tion, which may have been damaged during the malfunction.
3.7 (SERVICE) Check out appropriately all connections of the power
cables. If they are alright, uninstall the engine (in some cases it
is convenient to disassemble also the gearbox). Check out and
possibly replace the brushes.
3.8 Check out on the control box that between B2-C and B3-C
contacts there are 12/24V when the espective buttons are pressed.
If this should happen and one of the relays does not work, replace
the control box.
UK
1. By turning anticlockwise, remove the hand-wheel of the gypsy
through the manoeuvre handle.
2. Remove the 2 M6 screws from the side of the base that connect
the stripper and remove it.
3. Slip off from the shaft the upper clutch cone, the gipsy, and the
lower clutch cone.
4. Wash with running water. DO NOT USE WATER UNDER
PRESSURE.
5. Check that there is no evidence of corrosion or mechanical
stresses.
6. Reassemble by proceeding in the reverse order, remembering to
lubricate threads and all moving parts with grease.
6.2 Gipsy maintenance/replacement
7 TROUBLESHOOTING
Lofrans'
Bekijk gratis de handleiding van Lofrans SX1, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Lofrans |
| Model | SX1 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 2954 MB |
