Livarno Lux IAN 410820 handleiding
Handleiding
Je bekijkt pagina 18 van 111
18 GB/IE
Initial use/Maintenance and cleaning/DisposalPrior to installation/Initial use
Prior to installation
Important: The electrical connection must be
established by a qualified electrician or a person
trained to perform electrical installations.
This person must be familiar with the properties of
the light and the connection regulations.
Familiarise yourself with all the instructions and
diagrams in this manual, as well as with the
light itself, before you install it.
Before installation ensure that the circuit, to which
the light will be connected, is not energised. To
do so, remove the fuse or switch off the circuit
breaker in the fuse box (0 position).
Use a 2-pole voltage tester to verify cables are
not live.
Initial use
Mounting the light
Remove the base plate
1
from the lampshade
5
by turning it anticlockwise.
Remove both screwless clamps
6
and the
locking hooks
7
from the base plate
1
.
Hold the base plate
1
against the ceiling and
mark the drill holes using the holes in the base
plate
1
intended for the screws
2
.
Drill the holes (Ø 6 mm, approx 40 mm deep).
Be sure not to damage the power cable.
Insert the wall plugs
3
into the drilled holes.
If necessary, tap in with a hammer.
Feed the mains connection cable (external)
9
through the opening in the centre of the base
plate
1
(see Fig. A).
Note: Make sure that you do not push the
mains connection cable too far through the
opening, as the base plate
1
will then no
longer fit on the lampshade
5
.
Attach the base plate
1
to the ceiling using
the screws (see Fig. A).
Pull the protective tubes
4
over cables L and N
of the mains connection cable (external)
9
. Be
sure to correctly connect the individual conduc-
tors of the mains connection cable (external)
9
:
live conductor, black or brown = symbol L,
neutral conductor, blue = symbol N.
Note: This light has protection class
; the
earth wire should not be connected.
Now insert the screwless clamps
6
and the
locking hooks
7
into their intended positions
on the base plate
1
(see Fig. B–D).
Now attach the lampshade
5
by screwing it
clockwise onto the base plate
1
(see Fig. E).
Note: The arrows on the base plate
1
and
on the lampshade
5
must be opposite one
another (see Fig. H).
Replace the fuse or switch on the circuit breaker
(I setting) in the fuse box.
Inserting/replacing batteries
(remote control) (see Fig. G)
Note: Before first use, pull the insulating strip
12
out
of the battery compartment
11
.
If the range of the remote control
10
reduces, the
battery
13
needs to be replaced.
Push in the release lever and pull out the battery
compartment
11
.
If necessary, remove the old battery
13
.
Insert a new battery
13
in the battery compart-
ment
11
. Only use batteries
13
specified in
the chapter “Technical data”.
Note: Be sure to insert the batteries with the
correct polarity. This is indicated on the remote
control
10
.
Slide the battery compartment
11
back into the
remote control
10
.
Controlling light effects with
the remote control
Note: The transmitter for the remote control
10
is
located on the opposite side of the battery compart-
ment
11
. Ensure there are no obstacles between the
transmitter and the receiver.
ON/OFF = Switch light ON/OFF
Illuminant = Cold white/neutral white/
warm white
Bekijk gratis de handleiding van Livarno Lux IAN 410820, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Livarno Lux |
| Model | IAN 410820 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 10961 MB |
