Livarno Lux IAN 380905 handleiding
Handleiding
Je bekijkt pagina 14 van 60
14 GB/IE
The product must not be electrically connected
to another device.
If the product is not in use for any length of
time (e.g. holidays), disconnect it from the
power supply.
If you have any questions about the product or
are unsure about any of its aspects, please
seek the advice of an electrical equipment
specialist.
The product is only suited for use with the
included power adaptor
4
(Model No.
JT-DC30V7.2W-H4-IP44).
Please note that the power adaptor
4
continues
to draw a small amount of power even if the
product is turned off as long as the power
adaptor
4
is plugged into a power outlet.
To switch the product off completely, unplug
the power adaptor
4
from the socket.
The LEDs are not replaceable.
If the LEDs fail at the end of their lives, the entire
product must be replaced.
RISK OF EXPLOSION! Do
not use the product in explosive atmospheres
where flammable vapours, gases or dusts are
present.
Do not expose the product to any strong
vibrations or heavy mechanical stresses.
Make sure the lead wire
2
is not laid down in
areas where lawn mowers, trimmers, scissors or
similar cutting tools are used.
RISK OF INJURY! Make sure
that, when the LED tree
1
is removed, the stand
6
and ground spikes
7
are also removed, so
that they do not present any risk (e.g. risk of
stumbed by the stand or ground spikes).
The twigs of the LED tree
1
are made with
metal wire, which can cause scratches or dis-
coloration to delicate surfaces.
Installation
Note: Remove all packaging materials from the
product.
Remove the individual parts from the packag-
ing and mount the product according to figures
A–F. The site for the LED tree
1
must be se-
lected in a way that it is erected on a solid,
level and vibration-free base.
Unfold the stand
6
(see Fig. A).
Place the stand
6
on the selected location
(see fig. A).
For outdoor use: Anchor the stand
6
to the
ground using the ground spikes
7
.
Insert the lower part
1c
of the LED tree
1
into
the stand
6
and tighten the fastening screws
5
(see Fig. B and C).
Now insert the middle part
1b
into the lower
part
1c
of the LED tree
1
. Then insert the tip
1a
into the middle part
1b
of the LED tree
1
(see Fig. D).
Bend the individual branches of the LED tree
1
to the desired shape (see fig. E). Remind not to
bend all the branches just to one side.
The lead wire
2
must be unwound beforehand
when first use. Insert the connector of the lead
wire
2
into the socket of the power adaptor
4
and tighten the screw connection, in order to
prevent moisture from penetrating inside (see
fig. F). Pay attention to the sealing ring. Then
plug the power adaptor
4
into a socket.
Setup the LED tree
1
firmly to the ground and
make sure that the LED tree
1
is stable!
Timer function
The timer button
3
has three functions:
1 x push of the button:
The product lights up continuously.
2 x push of the button:
The product lights up continuously for 6 hours
and then switches itself off for 18 hours. The
product will then switch on again for 6 hours at
the allocated time and then switch off for
18 hours.
Note: The timer button
3
lights up when the
timer function has been activated.
3 x push of the button:
The product is switched off.
Bekijk gratis de handleiding van Livarno Lux IAN 380905, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Livarno Lux |
| Model | IAN 380905 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 5858 MB |
