Livarno Lux IAN 375304 handleiding
Handleiding
Je bekijkt pagina 49 van 77
49
GB/IE/NI/CY/MT
xings are best suited for the surface on
which you intend to mount the light. If
necessary, you should seek the advice of an
expert.
When deciding where to mount the
light, pay attention to the following:
Ensure the product illuminates the desired
area. Make sure that the motion sensor
4
covers the desired area.
The motion sensor has a maximum
detection range of 10m with a eld of view
of approx. 120°.
Ensure that the motion sensor
4
is not in a
position where street lighting will shine on it
at night. This may impair the function.
The recommended installation height is 2 to
4m. If possible, mount the Spotlight in a
position where it will not be exposed to dirt
or dust and is protected from rain (e.g.
under a roof overhang) and other
weathering effects.
Please note:
the solar panel
2
should be
positioned where it will be exposed to as
much direct sunlight as possible. Even partial
shade during the day can signicantly
impair the charging process.
Orientation:
The optimum alignment is facing south.
Choose an orientation facing slightly to the
west rather than slightly to the east.
z
Mounting the Spotlight
Transfer the positions of the guide holes
3
/
13
to the mounting point on the wall.
Drill two holes (dia. 6mm) and insert the
matching wall plugs
8
(see Figs. C and
G).
Mounting model 1020-B
Screw the screws
7
into the wall plugs
8
,
leaving a gap of approx. 3mm between the
screw head and the wall (see Fig. C).
Slot the guide holes
3
over the screws and
then slide the Spotlight along the guides to
x it in place (see Fig. C).
If necessary, adjust the gap between the
screw heads and the mounting surface to
provide a rm seating for the Spotlight.
Mounting model 1020-S
Screw the wall bracket
11
rmly in place
by inserting the screws
7
through the
guide holes
13
into the wall plugs
8
and
rmly tightening them (see Fig. G).
Fix the Spotlight to the wall bracket
11
by
loosening the Spotlight star knob
9
and
removing the screw
12
�
Align the holes in the Spotlight with the
holes in the wall bracket and slot the screw
12
through the holes (see Fig. F).
Screw the Spotlight star knob
6
onto the
screw and tighten it hand-tight. Check that
the product is xed rmly in place.
z
Positioning the Spotlight/
solar panel
Positioning model 1020-B
The Spotlight can be adjusted horizontally
(top/bottom) to an angle of up to 180° (see
Fig. D).
Loosen the two Spotlight star knobs
6
to
adjust the Spotlight (see Fig. B).
When the desired position is obtained,
tighten the star knobs again. If necessary,
use a screwdriver to hold the screw while
tightening the star knob.
Positioning model 1020-S
The Spotlight can be adjusted horizontally
(top/bottom) to an angle of up to 180° (see
Fig. H).
Loosen the wall bracket star knob
10
to
adjust the height of the Spotlight (see Fig.
H).
When the desired position is obtained,
Bekijk gratis de handleiding van Livarno Lux IAN 375304, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Livarno Lux |
| Model | IAN 375304 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 8675 MB |
