Handleiding
Je bekijkt pagina 40 van 46
Defect Cause Remedy
Frost formation on
the housing frame
and/or on the
inside of the door.
→ Door seal is damaged.
u
Replace the door seal.
→ You have set the temperature too
cold or you have not opened the
door often enough.
u
The appliance is not malfunctioning; simply remove any
condensation with a cloth.
9.3 Customer Service
First check whether you can remedy the fault yourself . If
this is not the case, please contact Customer Service.
You can find the address in the enclosed brochure “Liebherr-
Service” or at home.liebherr.com/service.
WARNING
Unprofessional repair!
Injuries.
u
Have any repairs and action - not expressly specified -
on the appliance and mains cable carried out by service
personnel only. (see8 Maintenance)
u
A damaged mains cable may only be replaced by the
manufacturer, the manufacturer’s Customer Service or a
similarly qualified person.
u
In the case of appliances with an IEC connector, the
change may be made by the customer.
9.3.1 Contacting Customer Service
Make sure you have the following appliance data at the
ready:
q
Appliance name (model and index)
q
Service no. (Service)
q
Serial no. (S no.)
u
Access the appliance information via the display
(see 6.2.15 Device information ) .
-or-
u
Refer to the type plate for appliance information.
(see 9.4 Type plate)
u
Note down appliance information.
u
Inform Customer Service: Report faults and the appliance
information.
w
This will help us to provide a fast and focussed service.
u
Follow any further instructions provided by Customer
Service.
9.4 Type plate
The type plate is inside the appliance. See appliance over‐
view.
Fig. 167
(1)
Appliance designation (3) Serial No.
(2) Service No.
10 Shutting down
u
Empty the appliance.
u
Switch off the appliance.
u
Pull the mains plug out of the socket.
u
Remove the IEC socket if required: Pull the IEC socket out
of the appliance plug and move it to the left and right at
the same time.
u
Clean appliance (see 8.3Cleaning the appliance) .
u
If present: Remove the covers and insulation from the
sensor feed-through to prevent mould forming.
u
Leave the door open so that no bad odours form.
Note
Damage to the appliance and malfunctions!
u
After shutting down, only store the appliance at the
permitted room temperature of between -10 °C and
+50°C.
11 Disposal
11.1 Preparing appliance for disposal
Liebherr uses batteries in some of its appli‐
ances. In the EU, for environmental reasons,
legislation obliges the end user to remove
these batteries before disposing of old appli‐
ances. If your appliance contains batteries, a
corresponding notice is attached.
Lamps If you can remove the lamps yourself without
destroying them, also remove these before
disposal.
u
Take the appliance out of operation.
u
If possible: remove lamps without destroying them.
11.2 Disposing of the appliance in an
environmentally friendly manner
The appliance still contains
valuable materials and must
be disposed of separately from
unsorted municipal waste.
Dispose of batteries separately
from the old appliance. To do
this, you can return the batteries
free of charge to retailers as
well as recycling centres and
collection centres for recyclable
materials.
Lamps Dispose of removed lamps
via the respective collection
systems.
Shutting down
40 * Depending on model and options
Bekijk gratis de handleiding van Liebherr SFTvh 1501 Perfection, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Liebherr |
| Model | SFTvh 1501 Perfection |
| Categorie | Vriezer |
| Taal | Nederlands |
| Grootte | 6540 MB |
