Handleiding
Je bekijkt pagina 32 van 38
Fig. 155*
► Unscrew the bracket of the water tank with a torx screw‐
driver.*
▷ The bracket remains attached to the side panel via
various connections and cannot be completely removed.*
Fig. 156
► Hold the rear panel with both hands at the bottom and
pull downward vigorously at the same time.
► Pull the rear panel out to the front by the bottom end.
▷ The rear panel has been removed.
If you want to continue operating the appliance with the
rear panel removed:
► Set the D-Value to D2. (see D-Value*)
Inserting the rear panel
Fig. 157
► Make sure the appliance is completely empty.
► Slide in the rear panel from below to the top.
► Press back vigorously on the left-hand side of the rear
panel.
▷ The rear panel clicks into place.
► Screw the water tank bracket firmly in place.*
► Insert the equipment parts.
► Set the D-Value to D1. (see D-Value*)
9.5.4 Clean the components
NOTICE
Improper cleaning!
Damage to the appliance.
► Only use soft cleaning cloths and ph-neutral all-purpose
cleaners.
► Do not uses abrasive sponges or steel wool which may
cause scratches.
► Do not use any sharp or abrasive cleaning agents, nor
any that contain sand, chloride or acid.
Clean with a soft, clean cloth, lukewarm water and some
detergent:
- Door rack
- Shelf
- Dividing shelf*
- VarioSafe*
- Compartment lid for EasyFresh Safe
- Drawer
Please note: Do not remove the magnet on the drawer.
The magnet ensures the functionality of the IceMaker.*
- Flexible ice compartment divider in the IceMaker's ice
cube drawer*
Clean with a damp cloth:
- Retractable rails
Please note: The grease in the tracks is used for lubrica‐
tion and must not be removed!
Wash in the dishwasher up to 60°C:
- Bottle rack
- Holder of the dividing shelf*
- IceMaker water tank and water tank lid*
- Ice cube tray*
- Ice cube scoop*
► To disassemble components: see the relevant section.
► Clean the components.
9.5.5 Cleaning the IceMaker*
There are various options for cleaning the IceMaker.
Cleaning is required in the following cases:
❑
Initial operation
❑
With water tank:*
If out of use for more than 48 hours.*
Ensure that the following conditions are met:
❑
Water tank is clean and has been filled. (see 8.9.1 Fill the
water tank*) *
❑
IceMaker drawer is emptied.
❑
IceMaker drawer is in place.
❑
The IceMaker is activated.
First use or after a long period of non-use
Clean the IceMaker with the TubeClean function.
► Put an empty 1.5 l vessel (max. height 10 cm) in the
drawer under the IceMaker.
► Activate the TubeClean function.
▷ The rinse process is prepared (max. 60 min.): Symbol
flashes.
▷ Water pipes are rinsed: Symbol flashes.
▷ Rinsing process is complete: Function turns off automati‐
cally.
► Remove the IceMaker drawer and remove the container.
► Clean the IceMaker drawer with warm water and a little
detergent.
► Push the IceMaker drawer in.
▷ The system starts making ice cubes automatically.
Without a water filter
► Dispose of any ice cubes that were made 24 hours after
the first ice cubes.
Maintenance
32 * Depending on model and options
Bekijk gratis de handleiding van Liebherr ICN 5103 Pure, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Liebherr |
| Model | ICN 5103 Pure |
| Categorie | Koelkast |
| Taal | Nederlands |
| Grootte | 5643 MB |
