Lectrosonics SMWB/E01 handleiding
Handleiding
Je bekijkt pagina 12 van 30
SMWB Series
LECTROSONICS, INC.12
Selecting Frequency Using Two Buttons
Hold the MENU/SEL button in, then use the and ar-
row buttons for alternate increments.
NOTE: You must be in the FREQ menu to access
this feature. It is not available from the main/
home screen.
Freq.
b 19
494.500
51
1 block steps
1.6 MHz steps to
nearest 100 kHz
channel
10 MHz steps
100 kHz steps
to next 100
kHz channel
100 kHz Mode
Freq.
b 19
494.525
51
1
4
1 block steps
1.6 MHz steps
10 MHz steps
25 kHz steps
25 kHz Mode
If the Step Size is 25 kHz with the frequency set between
even 100 kHz steps and the Step Size is then changed to
100 kHz, the mismatch will cause the hex code to display
as two asterisks.
494.525
-40
-20
0
b 19
Freq.
b 19
494.500
**
Step Size and
Frequency
mismatch
About Overlapping Frequency Bands
When two frequency bands overlap, it is possible to
select the same frequency at the upper end of one and
the lower end of the other. While the frequency will be the
same, the pilot tones will be dierent, as indicated by the
hex codes that appear.
In the following examples, the frequency is set to
494.500 MHz, but one is in band 470 and the other in
band 19. This is done intentionally to maintain compat-
ibility with receivers that tune across a single band. The
band number and hex code must match the receiver to
enable the correct pilot tone.
Freq.
b470
494.500
F4
Freq.
b 19
494.500
51
Make sure the
band number and
hex code match
the receiver setting
Selecting the Low Frequency Roll-o
It is possible that the low frequency roll-o point could
aect the gain setting, so it’s generally good practice to
make this adjustment before adjusting the input gain. The
corner frequency for the high-pass lter can be set to:
• LF 35 35 Hz • LF 100 100 Hz
• LF 50 50 Hz • LF 120 120 Hz
• LF 70 70 Hz • LF 150 150 Hz
The roll-o is often adjusted by ear while monitoring the
audio.
.
Rolloff
Compat
StepSiz
Phase
Rolloff
70 Hz
Selecting the Compatibility (Compat)
Mode
When used with a Lectrosonics Digital Hybrid Wireless
®
receiver, the best audio quality will be achieved with the
system set to the Nu Hybrid compatibility mode.
Rolloff
Compat
StepSiz
Phase
Compat
IFB
Use the UP and DOWN arrows to select the desired
mode, then press the BACK button twice to return to the
Main Window.
Compatibility modes are as follows:
Transmitter Models LCD menu item
SMWB/SMDWB:
• Nu Hybrid: Nu Hybrid
• Mode 3:* Mode 3
• IFB Series: IFB Mode
Mode 3 works with certain non-Lectrosonics models.
Contact the factory for details.
NOTE: If your Lectrosonics receiver does not
have Nu Hybrid mode, set the receiver to Euro
Digital Hybrid Wireless® (EU Dig. Hybrid).
Transmitter Models LCD menu item
SMWB/E01 and SMDWB/E01:
• Digital Hybrid Wireless
®
: EU Hybr
• Mode 3: Mode 3*
• IFB Series: IFB Mode
* Mode works with certain non-Lectrosonics models.
Contact the factory for details.
Bekijk gratis de handleiding van Lectrosonics SMWB/E01, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Lectrosonics |
| Model | SMWB/E01 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 7735 MB |
