KStrong UFL201101 handleiding
Handleiding
Je bekijkt pagina 3 van 12
3
The maximum arrest force of the personal energy absorber when dynamically tested in accordance with ANSI Z359.13 is 1800 lbs. The
maximum elongation of the personal energy absorber when dynamically tested in accordance with the same standard is 48 inches. When the
weight of the user is 220 lbs. (100 kg) with a free fall distance of 6 ft., the maximum allowable elongation is 37 inches (95 cm).
IMPORTANT INFORMATION:
• It is important to inspect the equipment according to the manufacturer’s instructions before each use.
• Inspection of equipment should be done on a regular basis by a qualied person and the results should be recorded in the inspection
log.
• DO NOT REMOVE product labels which include important warnings and information for the “Authorized Person”.
• “Authorized Person” is a person who is exposed to fall hazards during the course of their work. This individual requires formal
training in the use of personal fall protection equipment and systems. The term “Authorized Person” may be used interchangeably
with “User” and “End-User”.
• DO NOT ALTER the equipment in any way.
• Always send the equipment back to the manufacturer, or to the persons or entities authorized in writing by the manufacturer, for
any repairs if required.
• Never use any natural material like manila, cotton, etc. as part of the Fall Protection System.
• Fall protection equipment should only be used for the purpose for which it has been designed.
• This equipment should never be used for towing and hoisting or for any other purpose than its intended use.
• A competent person must ensure compatibility of the system to minimize any potential for accidental disengagement.
• Authorized persons or users shall be trained on all warnings and instructions provided in this manual.
• It is important for all authorized persons and users to refer to the applicable ANSI Standards and to the regulations governing
occupational safety.
• Take proper precautions to remove any debris, material, obstructions, etc., from the work area which could cause injury, or otherwise
interfere with the functioning of the system.
• KStrong Anchors should be used only with the combinations of components, sub-systems or both which may affect or interfere with
the safe function of one another. Be certain that connecting devices are compatible and that other elements of the PFAS are safe
and compatible before use.
• Always check for obstructions below the work area to make sure that the potential fall path is clear.
• Keep the equipment away from anything that could damage it such as sharp edges, rough or abrasive surfaces, high temperature
surfaces, heat and welding sources, moving machinery, electrical hazards, etc.
• It is important to keep in mind environmental hazards when selecting fall protection equipment.
• Do not expose the equipment to chemicals, highly corrosive or caustic environments, or to direct sunlight and UV radiation, which
may cause UV degradation.
• Such harmful environments require a more frequent inspection and servicing program of the fall protection equipment to maintain
the integrity and safety of the equipment. Contact KStrong if in doubt.
• All the synthetic material of fall protection equipment must be protected from slag, hot sparks, open ames or other heat sources.
• It is recommended that heat resistant materials are used in such applications. It is important to allow adequate fall clearance below
the work surface.
• Always have a Rescue Plan ready and at hand when using this equipment.
WARNING
• Immediately discard any product which is exhibiting unusual wear, deformity or deterioration.
• Immediately remove from service any equipment that has been subjected to a fall.
COMPONENT COMPATIBILITY:
Component compatibility with KStrong manufactured fall protection equipment is ensured by strictly following the instructions for each type of
equipment used. However, if the user utilizes combinations of components or sub systems that are manufactured by others, only a “qualied” or
“competent” person (as dened in OSHA) can ensure the compatibility. If substitutions or replacements are made with non-approved components
or sub systems, then this may severely affect the compatibility of the equipment, making the complete system unsafe for use.
COMPATIBILITY OF CONNECTORS:
To ensure the compatibility of the connectors with their connecting element, it is important to safeguard that the sizes and shapes of the
connectors and the connecting elements do not allow their gate mechanisms to open inadvertently, notwithstanding their orientation with each
other. All hooks, carabiners, D-rings and other such connectors must be capable of supporting a min. force of 5000 lbs. (23 kN). All connectors
must be compatible with all system components like anchorages, etc. Never use equipment which is not compatible as this may cause the
connectors to disengage unintentionally. All connectors must be compatible in shape and size. As per ANSI Z359.12 and OSHA, only self-locking
snap hooks and carabiners may be used.
Bekijk gratis de handleiding van KStrong UFL201101, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | KStrong |
| Model | UFL201101 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 1674 MB |
