Kimo CO2ST-S handleiding
Handleiding
Je bekijkt pagina 3 van 4
• Activate or deactivate an alarm
- Press the button for 3 seconds, “CONF” is displayed then “NEG”, meaning that the relay is in negative security, it is excited during
an alarm condition.
- If needed, press quickly on the button to switch the relay in positive security, the relay is de-energized during an alarm condition or a
current breaking, “POS” is displayed.
- Press 3 s on the button, “Buzz” screen is displayed with “ON” or “OFF” blinking. Briey press on the button to activate (“ON”) or
deactivate (“OFF”) (according to the last saved conguration) the buzzer during an alarm condition.
- Press 3 s the button, “Alarm” screen is displayed with “On” or “Off” blinking (according to the last saved conguration).
- Press quickly on the button, the display changes from “On” (activated alarm) to “Off” (deactivated alarm).
- Press 3 s the button to conrm the setting. If the alarm is deactivated, the instrument displays the measurement; if the alarm is
activated, the instrument displays the following setting.
• Set the action of the alarm (rising edge or falling edge)
The edge determines the action of the alarm according to the trespassing direction of the threshold(s).
Mode
Mode
Mode
Measurement (m) > Threshold (S) during the time-
delay T1: Alarm activation.
Measurement (m) < Threshold (S) - Hysteresis (H)
during the time-delay T2: Alarm deactivation.
Measurement (m) < Threshold (S) during the time-
delayT1: Alarm activation.
Measurement (m) > Threshold (S) + Hysteresis (H)
during time-delay T2: Alarm deactivation.
The alarm goes off when the measurement is
outside the low and high thresholds.
Rising edge Falling edge Monitoring
- Press briey on the button to select the trespassing direction then press the button more than 3 seconds to validate this direction
and set the thresholds.
• Set the threshold(s) value
The rst digit blinks, it corresponds to the positive (0) or negative (-) setting of the threshold value. Press briey on the button to select
the sign for the threshold value. Press on the button more than 3 seconds to validate.
The second digit blinks, press briey on the button to scroll the numbers. Press the button more than 3 seconds to validate.
Repeat the process until the last digit to congure the threshold value, validate the threshold and go to the following setting.
If the monitoring edge has been selected, the transmitter displays the setting of the second threshold.
• Set the hysteresis
The hysteresis is only for the rising edge and the falling edge modes.
In rising edge mode, the hysteresis allows to the transmitter to stay in alarm when the measurement is between the threshold and the
threshold minus the hysteresis.
Ex: for a 1000 ppm threshold and a 100 ppm hysteresis, the instrument will stay in alarm when the measurement will be between
1000 and 900 ppm.
In falling edge mode, the hysteresis allows to the transmitter to stay in alarm when the measurement is between the threshold and the
threshold plus the hysteresis.
Ex: for a 1000 ppm threshold and a 100 ppm hysteresis, the instrument will stay in alarm when the measurement will be between
1000 and 1100 ppm.
The rst digit blinks, set it pressing the button briey several times then press on the button more than 3 seconds to set the following digit..
Once the hysteresis is set, press the button more than 3 seconds to validate and set the time-delays.
• Set the time-delay 1 and the time-delay 2 (600 seconds maximum)
- In rising edge mode, the time-delay 1 corresponds to the time lag before the alarm goes off when the threshold has been reached.
The time-delay 2, corresponds to the time lag before the alarm stops when the measurement is lower than the threshold minus the
hysteresis.
Rising edge(1 threshold): the alarm goes off when the measurement exceeds the threshold and stops when it is
below the threshold.
Falling edge(1 threshold): the alarm goes off when the measurement is below the threshold and stops when it
exceeds the threshold.
Monitoring (2 thresholds): the alarm goes off when the measurement is outside the dened low and high thresholds.
Bekijk gratis de handleiding van Kimo CO2ST-S, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Kimo |
| Model | CO2ST-S |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 1204 MB |
