Jung SITMA5073 handleiding
Handleiding
Je bekijkt pagina 90 van 140
7 Programming
Remarks
The In-Home bus can be pro-
grammed in three ways:
1 Programming – manual
For more information, see
page90
2 Programming – Plug+Play
For more information, see
page118
3 Programming – with PC
For more information, see
page122
Important remarks prior to pro-
gramming
• The entire installation must have
been completed. When program-
ming using the Plug+Play method,
the housing of the bus indoor
devices must not yet be closed. The
Siedle Scope base station must not
be connected to the In-Home bus.
• Before starting programming, all
buttons should be inscribed to allow
them to be assigned to the relevant
bus indoor devices.
• It is only ever possible to activate
one door loudspeaker in the pro-
gramming mode.
• If an already programmed call
button is pressed for longer than
3seconds in the programming mode
at the activated door loudspeaker,
after one second a warningtone is
sounded, and after 3seconds the
conrmation tone. After this, the
call button is deleted if there was no
bus indoor device active. However,
if there is a bus indoor device active
at this moment, the button is over-
written with the new address.
• All BNG/BVNG650-… units must
be connected to mains voltage of
230VAC.
• In multiple line systems with sev-
eral BNG/BVNG650-… units, actu-
ating the Prog. mode button at one
BNG/BVNG650-… switches all other
connected BNG/BVNG650-… units
to the programming mode.
• In multiple line systems, at each
BNG/BVNG650-… a different
address must be set. The number
“0“ cannot be used as an
address!
• In multiple line systems bus power
supply accessory ZBVG650-…
must be additionally plugged
into one BNG/BVNG650-… The
bus video line rectier accessory
ZBVNG650-… must be pIugged into
each BVNG650-…
Programming – manual
Procedure:
On principle, the In-Home bus can
be commissioned and programmed
by one person. However, as work
has to be executed both at the door
loudspeaker and the bus indoor
device, we recommend that commis-
sioning be carried out by two people
for larger-scale projects.
• Complete the installation
• Check the switch positions at the
BNG/BVNG650-…, in new systems
set the switch setting to Norm.
• Activate the programming mode
at the bus line rectier
• Set the door station to the pro-
gramming mode
• Program the users
• Quit the programming mode
While the bus line rectier is in the
programming mode, several steps
can be programmed in sequence.
There is no need to quit the pro-
gramming mode after every oper-
ation.
Handsfree bus telephones and
Siedle Scope
Picking up and replacing the receiver
are no longer necessary when
using handsfree bus telephones
AIB/VIB150-…/BFC/BFCV/BVPS/
BVPC850-… and with Siedle Scope.
The AIB/VIB150-… switch to the
programming mode by pressing the
speech button.
The BFC/BFCV/BVPS850-… switch
to the programming mode by
pressing the light button.
With Siedle Scope, the Prog. button
on the base station has to be
pressed. Once the programming
step has been performed, the device
switches back to the idle status.
All other programming steps are
identical.
Deluxe bus video panel
With the BVPC850-… the program-
ming mode is activated via the menu
user interface. Tab:
> Settings
> Installation
> Start programming mode
> Start.
The device is then switched to the
programming mode. Once the pro-
gramming step has been performed,
the device switches back to the idle
status. All other programming steps
are identical.
90
Bekijk gratis de handleiding van Jung SITMA5073, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Jung |
| Model | SITMA5073 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 13662 MB |
