JET JWJ-8HH-BLK handleiding
Handleiding
Je bekijkt pagina 4 van 28
4
3.0 Safety Warnings
1. Read and understand the entire owner's
manual before attempting assembly or
operation.
2. Read and understand the warnings posted on
the machine and in this manual. Failure to
comply with all of these warnings may cause
serious injury.
3. Replace the warning labels if they become
obscured or removed.
4. This jointer is designed and intended for use by
properly trained and experienced personnel
only. If you are not familiar with the proper and
safe operation of a jointer, do not use until
proper training and knowledge have been
obtained.
5. Do not use this jointer for anything other than its
intended use. If used for other purposes, JET
disclaims any real or implied warranty and holds
itself harmless from any injury that may result
from that use.
6. This machine has an industrial-grade low-
friction corrosion-resistant coating we call JET
Black. This coating is on the infeed and outfeed
tables and the fence. While the JET Black
coating is durable, it can be damaged if metal
or other hard and/or sharp objects strike,
gouge, or scratch the surface. Significant
damage to the coating may affect its
performance.
7. Always wear approved safety glasses/face
shields while using this jointer. Everyday
eyeglasses only have impact resistant lenses;
they are not safety glasses.
8. Before operating this jointer, remove tie, rings,
watches and other jewelry, and roll sleeves up
past the elbows. Do not wear loose clothing.
Confine long hair. Non-slip footwear or anti-skid
floor strips are recommended. Do not wear
gloves.
9. Wear ear protectors (plugs or muffs) if noise
exceeds safe levels.
10. Do not operate this machine while tired or under
the influence of drugs, alcohol, or any
medication.
11. Make certain switch is in OFF position before
connecting machine to power supply.
12. Make certain machine is properly grounded.
13. Make all machine adjustments or maintenance
with machine unplugged from the power
source.
14. Remove adjusting keys and wrenches. Form a
habit of checking to see that keys and adjusting
wrenches are removed from the machine
before turning it on.
15. Keep safety guards in place at all times when
machine is in use. If removed for maintenance
purposes, use extreme caution and replace the
guards immediately after completion of
maintenance.
16. Check damaged parts. Before further use of the
machine, a guard or other part that is damaged
should be carefully checked to determine that it
will operate properly and perform its intended
function. Check for alignment of moving parts,
binding of moving parts, breakage of parts,
mounting and any other conditions that may
affect its operation. A guard or other part that is
damaged should be properly repaired or
replaced.
17. Provide for adequate space surrounding work
area and non-glare, overhead lighting.
18. Keep work area clean. Keep floor around
machine clean and free of scrap material, oil,
and grease. Dirty and cluttered floors invite
accidents.
19. Keep visitors a safe distance from the work
area. Keep children away.
20. Make your workshop child proof with padlocks,
master switches, or by removing starter keys.
21. Give your work undivided attention. Looking
around, carrying on a conversation, and “horse-
play” are careless acts that can result in serious
injury.
22. Maintain a balanced stance at all times so that
you do not fall, slip, or lean into the knives. Do
not overreach or use excessive force to perform
any machine operation.
23. Use the right tool at the correct speed and feed
rate. Do not force a tool or attachment to do a
job for which it was not designed. The right tool
will do the job better and more safely.
24. Use recommended accessories; improper
accessories may be hazardous.
25. Maintain control of workpiece at all times. Make
sure the work piece is stabilized during
operation. Firmly hold workpiece down against
table while jointing. Always use a hold-down or
push block when surfacing stock.
26. When working a piece of wood on the jointer,
follow the 3-inch rule: The fingers and hands
must never be closer than 3 inches to the
cutterhead at any time.
27. Do not joint material shorter than 10-inches,
narrower then 3/4-inch, or less than 1/4-inch
thick.
28. Do not make cuts deeper than 1/8-inch for
jointing cuts and 1/16-inch for planing cuts.
Deeper cuts could overload the machine and
increase the chance of kickback.
29. Never apply pressure to stock directly over the
cutterhead. This may result in the stock tipping
Bekijk gratis de handleiding van JET JWJ-8HH-BLK, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | JET |
| Model | JWJ-8HH-BLK |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 9382 MB |
