IOGEAR GCS1218TAA3 handleiding
Handleiding
Je bekijkt pagina 22 van 36
22
Chapter 3 - Operation
Powering On
When powering on, resetting, or power cycling IOGEAR Secure KVM Switch, the switch will perform a
self-test to check the unit’s integrity and security functions.
During the self-test
❒ All Port and CAC LEDs will turn ON and then OFF
❒ The KVM focus will be switched to Port 1 when the self-test completes successfully (Port 1 LED lights
bright orange)
Self-test failure
In case of a self-test failure, IOGEAR Secure KVM Switch becomes inoperable. Front panel LED
combination lights up, indicating the potential cause to the failure (such as button jam or KVM integrity
compromise):
❒ A pre-dened combination of Port and CAC LED indicates the cause to the failure.
❒ If all front panel LEDs (except for Power LED) ash continuously, then either KVM tampering is
detected or a self-test failure has occurred (except for Pushbutton jam; see below)
❒ If Pushbutton jam is detected, both the Port and CAC LEDs will ash
For security, IOGEAR Secure KVM Switch becomes inoperable if self-test fails. Please verify your KVM
installation, pushbuttons, and power cycle the Secure KVM Switch again if this should happen. If the self-
test failure remains, stop using the Secure KVM Switch immediately, remove it from service, and contact
your IOGEAR dealer.
After the IOGEAR Secure KVM Switch is powered on and ready, power on your computers. By default,
the IOGEAR Secure KVM Switch will switch to Port 1 after a successful self-test.
IOGEAR Secure KVM Switch lters and emulates both the mouse and keyboard on each port after the
unit is powered on. If the keyboard, mouse, monitor, or Smart Card / CAC reader fails to operate properly,
make sure that only qualied and authorized peripherals are connected. Next, power off IOGEAR Secure
KVM Switch and check all cable connections. Then, power the unit back on again.
Manual Switching
For increased security, IOGEAR Secure KVM Switch offers manual port-switching only. This is achieved
by pressing the port selection pushbutton located on the Secure KVM switch’s front panel. Press and
release a port selection pushbutton to bring the KVM focus to the computer attached to its corresponding
port (see Port ID Numbering below). To meet maximum security and channel isolation requirements, the
keyboard, mouse, video monitor, audio, and USB CAC reader ports will be switched together.
The Selected Port LED lights orange to indicate that the computer attached to its corresponding port has
the KVM focus (keyboard, mouse, monitor, audio, and CAC reader).
The PC that has the port focus on should be able to detect the peripherals after port switching. If the PC
fails to detect the keyboard, mouse, or CAC reader:
• Please verify if you are using qualied Keyboard, Mouse, or CAC reader
• Please verify if your keyboard, mouse, or CAC reader has failed
• For USB CAC Card readers (USB authentication devices), please make sure that the USB CAC cable
has been securely connected and the CAC function on the Secure KVM switch is enabled.
• Please verify if the USB CAC reader has been authorized for the corresponding port
Port ID Numbering
Each KVM port on IOGEAR Secure KVM Switch is assigned a port number (1-2 for 2-Port models; 1-4
for 4-Port models; 1-8 for 8-Port models). The port numbers are marked on the rear side of the switch.
See Rear View section in this manual. The port ID of a computer is derived from the KVM port number to
which it is connected.
Bekijk gratis de handleiding van IOGEAR GCS1218TAA3, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | IOGEAR |
| Model | GCS1218TAA3 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 3133 MB |
Caratteristiche Prodotto
| Kleur van het product | Zwart, zilver |
| Ingebouwd display | Nee |
| Gewicht | 2950 g |
| Breedte | 430 mm |
| Diepte | 203 mm |
