Handleiding
Je bekijkt pagina 36 van 76
English • 36
cleaning and maintaining the induction hob
7
DAILY CLEANING
Warning
:
Allow all cooking zones to cool down before cleaning the induction hob and activate the child lock before you begin.
Warning: When spilling sugar, immediately clean the hob to prevent the sugar from burning into the surface. Be careful,
the cooking zones can be hot.
Careful: Do not use abrasive cleaning agents, aerosols, abrasive sponges or sharp objects that have not been
developed for this purpose.
1. Lock the hob.
2. Remove spilled food. Use a damp cloth and a mild cleaning agent.
3. Clean the appliance daily. Use a damp cloth and a mild cleaning agent.
4. Dry the appliance Use kitchen towel for this or a dry tea towel.
5. In case of severe contamination, clean the appliance with a cleaning agent that is specifically suitable for an induction
appliance.
6. When food has been spilled on the control elements, the appliance may give a beep sound and switch off automatically.
Wipe up what has been spilled with a wet cloth and dry the area before you switch the appliance on again.
breakdowns & solutions
8
GENERAL PROCEDURE FOR TROUBLESHOOTING
1. Use the troubleshooting table and breakdown codes to find a solution for the problem.
2. If you cannot find a solution, or if the breakdown code keeps returning, contact the Inventum service department.
Breakdown (code) Cause What to do
The induction hob doesn't work, despite
the fact the plug is inserted in the socket.
No power supply. Check that the plug is properly inserted
in the socket and that there is power on
the socket.
The hob cannot be activated.
The control panel is locked by means of the
child lock.
Unlock the control panel.
See section 'Locking and unlocking
operation of the appliance'.
The control panel is covered with dirt or
a thin film of water.
Clean the appliance.
See section 'Daily cleaning'.
The induction hob stops all of a sudden
during use and the display shows
.
An unsuitable pan is being used.
Use a pan suitable for induction with the
correct diameter (minimum Ø 14 cm).
The diameter of the pan used is too small.
The display switches on, but the
induction hob does not heat up.
The induction hob is too hot. The ambient temperature can be
too high. Check if the air openings
are blocked.
A cooking zone switches off
automatically and the display shows [ H ].
The maximum cooking time has been
reached.
Switch on the cooking zone again.
Some pans make a crackling
or clicking noise.
This can be caused by the structure of the
cookware (layers of different materials
vibrate differently).
This is normal for cookware and does
not indicate an error. Make sure you
are using good cookware that is suitable
for an induction appliance.
The appliance makes a low
buzzing noise at a high heat setting.
This is caused by the technology of cooking
with induction.
This is normal, but the noise should
become less or disappear completely
when you lower the power level.
Out of the appliance comes the noise
of the fan.
A cooling fan has been integrated
in your appliance in order to prevent
the electronics from overheating.
The fan may even continue to run after
switching off the appliance.
This is normal and you do not have
to do anything. Do not remove the plug
from the socket while the fan is running.
The glass plate is cracked.
Hazard! Switch off the power supply
and remove the plug of the appliance.
Contact the Inventum service department.
Bekijk gratis de handleiding van Inventum IKI8045, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Inventum |
| Model | IKI8045 |
| Categorie | Fornuis |
| Taal | Nederlands |
| Grootte | 6848 MB |
