Intex Krystal Clear 126688 handleiding
Handleiding
Je bekijkt pagina 11 van 26
(379IO) MODEL LS5220/5230 SALTWATER SYSTEM ENGLISH SIZE: 7.5” X 10.3” PANTONE 295U 09/30/2024
SAVE THESE INSTRUCTIONS
Page 10
379
A
English
SALT & POOL WATER VOLUMES
• Which kind of salt to use:
A specific type of salt must be used in swimming pools to protect the equipment. When buying salt, check that the salt
conforms with the EN16401 standard for Chemicals for use in swimming pools. Consult your local pool store or contact the salt
manufacturer if you need help with verifying you have the correct salt.
Do not use “NON CHLORIDE ION SALTS”.
Use only
pure (sodium chloride) salt such as common table salt, iodized salt, naturally evaporated sea salt, etc. Salt containing anti-caking
agent (E535) is suitable.
When choosing the pool salt for use within the EU, please also note that the European Chemicals Agency (ECHA) requires that
salt (sodium chloride) be used from registered/authorized manufacturers listed in the ECHA Article 95 List in accordance with the
Biocidal Product Regulation (BPR, Regulation (EU) 528/2012). For more information, please consult ECHA’s website at https://
echa.europa.eu/information-on-chemicals/active-substance-suppliers.
• Optimum Salt Level
The ideal salt level in the pool water is between 800-1800 ppm (parts per million). The optimal level is 950 ppm.
The final salt level detected in the water
=
initial natural minerals
+
added salt level.
The minerals level in fresh water
varies from region to region and local water condition.
For first-time pool or Saltwater System users:
After the system is setup and before adding salt to the pool, turn on the system and press the “
MODE
” ( ) button once to
activate the salt level detection function. The number (in ppm) on the display corresponds to the natural minerals present in the
water, such as iron ions, calcium, etc. Record this number as this will be the starting base for future reading. Add salt to the pool
according to “
Adding Salt
” section. Check the salt level after 24 hours to ensure it is within 800-1800 ppm.
For existing pools with Saltwater System or using chemicals sanitizer that are upgrading to model QS700 PLUS:
After the system is setup, press ( ) button once to activate the salt level detection function. If the number (in ppm) shown on
the display exceeds 1800 ppm, lower the salt level by following the steps in “
SALT & POOL WATER VOLUMES, Removing
Salt
” section. Check the salt level again after 24 hours to ensure it is within 800-1800 ppm.
• Adding Salt
1
. Switch the filter pump on.
2
. Keep the Saltwater System turned off.
3
. Add salt according to the “
SALT TABLE
” section. Alternatively see “
Alternative Salt Level Measurement
” section.
4
. Evenly spread the salt around the inside of the pool.
5
. Brush the pool bottom to speed up the dissolving process and run the filter pump for 24 hours.
6
. After 24 hours, press ( ) button to turn on the system, press ( ) button once to activate the salt level detection
function. Check the salt level is within 800-1800 ppm. The number on the display will start changing and the latest salt level
reading will be displayed after 3 minutes. See “
Salt / Temperature Detection Display Mode
” section for details.
7
. Press ( ) button until “00H” or operating hour is flashing on the display and press the timer ( ) button to set the
desired operating time. See “
OPERATING INSTRUCTIONS
” section.
• Removing Salt
1
. If too much salt has been added, the system will display code “E92”
(see “
LED CODE CHART
”). To lower the salt level, partially drain
and refill approximately 40-70% of the pool’s water, see right table.
2
. If the pool water level has dropped below the recommended fill level,
add fresh water until the recommended level.
3
. Press ( ) button to turn on the system and press the mode ( )
button once to activate the salt level detection function. Check the
salt level is within 800-1800 ppm. The number on the display will start
changing and the latest salt level reading will be displayed after 3 minutes.
NOTE:
First install the Saltwater System, turn on the system and press ( ) button once to check the salt level in the pool.
• Alternative Salt Level Measurement
1
. After the system is setup and before adding salt to the pool, turn on the system and press ( ) button
once to activate the salt level detection function. The number (in ppm) shown on the display corresponds to
the natural minerals present in the water, such as iron ions, calcium, etc. Record this number of
initial salt
concentration (C
0
)
as this will be the starting base for future reading.
2
. Add
5kg (S
1
)
salt to the pool, turn on the pump, run the filter pump for 2 hours to dissolve the salt. Then, turn
on the saltwater system and press ( ) button again to test the
current salt level (C
1
)
.
3
. Scan the QR code to open the “salt calculator” program and input the following data for
C
0
(ppm), C
1
(ppm)
and S
1
(5kg)
. The program will calculate the
additional amount of salt “S
2
” (kg) needed automatically
.
The calculation formula is: S
2
=
S
1
x [950-(C
1
-C
0
)]/(C
1
-C
0
) in kg.
Salt level (ppm)
Pool water to be
drained and relled
1800 - 2200 40%
2200 - 2600 50%
2600 - 3200 60%
3200 - 4000 70%
Salt calculator
QR Code
Bekijk gratis de handleiding van Intex Krystal Clear 126688, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Intex |
| Model | Krystal Clear 126688 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 5319 MB |
