Intermatic PE953 handleiding
Handleiding
Je bekijkt pagina 34 van 51
34 Multi-Wave PE953 Installation Guide
Copyright © 2011 Intermatic, Inc.
Removing Z-Wave Devices from Scenes
IfaZ-Wavedeviceisremovedfromanetworkforanyreasonwhatsoever,
you should go through this procedure to maximize prompt system
response.Otherwise,systemnetworkcongurationwillbecorruptedand
communications between the system devices may be degraded and/or lost
since the network will still retain information about the removed device(s).
NOTE: If you’re reassigning the device to a
different scene, rst remove it from its existing
scene, then include it into the new scene.
1. Ifnecessary,pressandreleaseanybuttononthe
Hand-Held Controller to wake it from sleep. If the
screen is not displaying LEARN MODE, press and
hold the <P/S> and <ENTER> buttons at the same
time to put the device into programming mode. You
are in programming mode when the LEARN MODE
screen is displayed, as shown at the right.
2. Press the <5> button to remove a device to the
scene. The screen displays PRESS 1-5 TO CHOOSE
THESCENETODELETETHEDEVICEFROM,as
shown:
Press one of the buttons (<1> through <5>) for
the scene you want the device removed from. The
screendisplaysPRESSBUTTONONDEVICETOBE
REMOVED, as shown:
3. Press the button on the Z-Wave device for removing
thedevicefromascene(refertothemanufacturer’sinstructions).The
screendisplaysWORKINGfollowedbySUCCESSFUL.Thedeviceisnow
removed from the scene.
4. Press the <ENTER> button if you wish to return to the Main screen.
Removing Z-Wave Devices from a Network
IfaZ-Wavedevicefromonenetworkisbeingaddedtoanotheroris
simply being removed from a network it is currently a part of ,it should be
removedfromtherstnetwork(bybeing“reset”)beforeaddingittothe
second.Otherwise,systemnetworkcongurationwillbecorruptedand
communications between the system devices may be degraded and/or lost
since the network will still retain information about the removed device(s).
1. Ifnecessary,pressandreleaseanybuttononthe
Hand-Held Controller to wake it from sleep. The
Hand-Held automatically displays the LEARN
MODE screen, as shown. If the screen is not
displaying LEARN MODE, press and hold the <P/
S> and <ENTER> buttons at the same time to put
the device into programming mode. You are in
programming mode when the LEARN MODE screen
is displayed, as shown at the right.
2. Press the <2> button to reset the device. The screen
displaysPRESSBUTTONONDEVICETO
RESET, as
shown:
3. Press the button on the Z-Wave device for resetting the device (refer to
themanufacturer’sinstructions).ThescreendisplaysWORKINGfollowed
by SUCCESSFUL. The device is now removed from the network.
4. Press the <ENTER> button if you wish to return to the Main screen.
Setting Up Z-Wave Associations with Capable Devices
An “Association” is a feature supported by certain Z-Wave devices where
Z-Wave device other than the PE953 controller can be used to control other
Z-Wave devices in the network (e.g., a Z-Wave
switch that controls other
Z-Wave
devices).
Within a PE653/953 network, setting up an association with one of these
Z-Wave
devicesmakesitpossibletocontrolCircuit1(thelterpump)of
the PE653 in an ON/OFF basis along with lighting or other features being
controlled by another Z-Wave device, independent of the Hand-Held
Controller.
NOTE: Before you can create an Association, the capable Z-Wave
device
must rst be included in the network.
1. Ifnecessary,pressandreleaseanybuttononthe
Hand-Held Controller to wake it from sleep. If the
screen is not displaying LEARN MODE, press and
hold the <P/S> and <ENTER> buttons at the same
time to put the device into programming mode. You
are in programming mode when the LEARN MODE
screen is displayed, as shown at the right.
2. Press the DOWN button once to display the CNTRL
OPTIONscreen,asshown:
3. Press button <5> toselectSETUPASSOCIATIONS.
The screen displays two choices, as shown:
4. Press button <1> toselectADDDEVICE.Thescreen
addsthewords:PRESSBUTTONONTHEDEVICE
CONTROLLINGTHEASSOCIATIONasshown.This
is the association-capable Z-Wave device you want
to use to control the other devices you plan to add
to the association.
5. Press the button on the device (the same button
used for including the device into a network.
Refertothemanufacturer’sinstructions.)that will
control the association. The screen displays: PRESS
THEBUTTONONTHEDEVICETOADDTOTHE
ASSOCIATION.
Bekijk gratis de handleiding van Intermatic PE953, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Intermatic |
| Model | PE953 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 8177 MB |
