Intermatic PE953 handleiding
Handleiding
Je bekijkt pagina 30 van 51
30 Multi-Wave PE953 Installation Guide
Copyright © 2011 Intermatic, Inc.
Section 4:
Programming for Use with Z-Wave
Home Control Devices
Models PE653 5-Circuit Digital Control and PE953 Remote Controller
are compatible with Z-Wave enabled networks. Z-Wave enabled devices
displaying the Z-Wave logo can be used with the PE653 and PE953
regardless of the manufacturer. Each Z-Wave enabled device is designed
to act as a repeater, re-transmitting the RF signal around obstacles and
radio dead spots when possible to ensure that messages are received by the
intended destination device.
IfyouwouldliketoaddZ-Wavehomecontroldevicestoyournetwork,
you need to include the devices into the network, and then assign them to
Scenes for their day-to-day operation.
Deleting Any Existing Programming
Perform this procedure with each Z-Wave device you plan to include into
the network to make sure that any existing programming within these
devices is deleted.
1. Ifnecessary,pressandreleaseanybuttononthe
Hand-Held Controller to wake it from sleep. If the
screen is not displaying LEARN MODE, press and
hold the <P/S> and <ENTER> buttons at the same
time to put the device into programming mode. You
are in programming mode when the LEARN MODE
screen is displayed, as shown at the right.
2. Press and release the <2> function button to
select RESET DEVICE. The screen refreshes with
instructionstoPRESSBUTTONONDEVICETO
RESET, as shown.
3. Press the button on the Z-Wave home control
device you want to remove from the network (refer
tothemanufacturer’sinstructions).
Iftheactionissuccessful,thescreendisplaysthe
word SUCCESSFUL, as shown, then returns to the
programming screen.
NOTE: If you are seeing the word FAILURE at the bottom of the screen,
carefully repeat the procedure. If the problem persists, contact Intermatic
Customer Service. For assistance with any non-Intermatic devices, you
may need to contact that manufacturer’s customer support department.
4. Repeat this procedure for all other Z-Wave home control devices that are
to be part of the network.
5. Press the <ENTER> button if you wish to return to the Main screen.
Including Z-Wave Devices into the Network
This procedure includes Z-Wave devices into a network controlled by the
PE953Hand-HeldController.ThePE953ispre-conguredtooperatewith
the PE653 Receiving Device. The PE953 can also operate as a stand alone
Z-Wave remote controller. Z-Wave devices from other manufacturers may
be part of the same network as the PE953 and PE653, and depending on
supported features, can act as repeaters.
1. Ifnecessary,pressandreleaseanybuttononthe
Hand-Held Controller to wake it from sleep. If the
screen is not displaying LEARN MODE, press and
hold the <P/S> and <ENTER> buttons at the same
time to put the device into programming mode. You
are in programming mode when the LEARN MODE
screen is displayed, as shown at the right.
2. Press and release the <3> function button to select
INCLUDE DEVICE. The screen refreshes with
instructionstoPRESSBUTTONONDEVICETO
INCLUDE,asshown.
3. Press the button on the Z-Wave device for including
thedeviceinanetwork(refertothemanufacturer’s
instructions).
Iftheactionissuccessful,thescreendisplaysthe
word SUCCESSFUL, as shown, then returns to the
programming screen.
NOTE: If the two devices are not successfully linked and you are seeing
the word FAILURE at the bottom of the screen, carefully repeat the
procedure. If the problem persists, contact Intermatic Customer Service.
4. Repeat this procedure for all other Z-Wave home control devices that are to be
part of the network.
5. Press the <ENTER> button if you wish to return to the Main screen.
Including the PE653 Receiver onto a non-Multi-Wave remote
controller
The PE653 is a Z-Wave compliant device that may be included into networks
createdbyothermanufacturer’sZ-Wavecompliantcontrollers.
ToincludethePE653intoanothermanufacturer’scontroller:
1. 1.Activatethecontroller’sINCLUDEfunctionaccordingtothat
manufacturer’sinstructions.
2. 2.PressandreleasetheINCLUDEbuttononthePE653.
Iftheincludewassuccessful,theredashingLEDonthePE653willchange
tosteadyON.(ThesteadyONLEDwillashrapidlywheneveranother
device is communicating with it.)
ToexcludethePE653fromanothermanufacturer’scontroller:
1. Activatethecontroller’sEXCLUDEfunctionaccordingtothat
manufacturer’sinstructions.
2. PressandreleasetheINCLUDEbuttononthePE653.
Iftheexcludewassuccessful,theredashingLEDonthePE653willchange
fromsteadyONtoslowlyashingONandOFF.
Bekijk gratis de handleiding van Intermatic PE953, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Intermatic |
| Model | PE953 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 8177 MB |
