Intermatic PE953 handleiding
Handleiding
Je bekijkt pagina 26 van 51
26 Multi-Wave PE953 Installation Guide
Copyright © 2011 Intermatic, Inc.
Section 3:
Advanced Features
The PE953 controller is able to listen to Z-Wave commands while the
controller is awake. (For example: requesting the controller to report Version
orManufacturerSpecicinformation.)
To wake up the controller, press any key.
Conguring Two or More Hand-Held Controllers
ManyinstallationswillnditconvenienttousetwoHand-HeldControllers.
Once you have linked and programmed one Hand-Held to the Receiving
Device,it’seasytoaddadditionalunits.
NOTES: The rst Hand-Held you link to the Receiving Device is considered
the PRIMARY control and all other Hand-Held units are SECONDARY.
• Only the PRIMARY Controller can be used to add or remove devices
from a network in the Intermatic Multi-Wave system.
• SECONDARY controllers cannot add or remove devices from the
network in the Intermatic Multi-Wave system — they can only
control devices on the network.
You can tell the status of a Hand-Held from the VER (version) code at the
top right corner of the display on the programming screens: the letter “P”
= PRIMARY; the letter “S” = SECONDARY.
The PRIMARY control must be used to “introduce” or include any
additional (SECONDARY) Hand-Held units to the system.
If the PRIMARY Hand-Held must be replaced (due to loss, damage, etc.,),
you must reprogram from scratch to create a new PRIMARY unit, then
reprogram any additional Hand-Helds as SECONDARY controls.
1. Ifnecessary,pressandreleaseanybuttononthe
Hand-Held Controller to wake it from sleep. If
the screen is not displaying LEARN MODE, press
and hold the <P/S> and <ENTER> buttons at the
same time to put the device into programming
mode. You are in programming mode when the
LEARN MODE screen is displayed, as shown at
the right.
2. Press the DOWN arrow button to view the
CNTRLOPTIONscreenasshown
3. Press the <2>buttontoselectCONTROLLERCOPY.
4. On the Primary Hand-Held used to set up and
congurethenetwork,pressandreleasethe<3>
button to select SEND NET AND CONFG.
5. On the new Hand-Held you are adding to the network, follow Steps 1-3,
then press and release the <4> button to select RECV NET AND CONFG.
ThewordsINCLUDINGDEVICEwillappearatthebottomofthe
primarycontroller’sscreen.Thescreenwillbrieydisplaythewords
SENDINGNETINFO,thenSENDINGSCENEINFO,thenSENDING
CFGINFOduringthetransferofinfotothesecondarydevice.Aftera
fewsecondsthecontrollerwillreturntotheCNTRLCOPYscreen.
ThewordsWAITINGFORINCLUDEwillappearatthebottomofthe
secondarycontroller’sscreen.Uponcompletionoftheinfotransferthe
word SUCCESSFUL will then appear. After a few seconds the control-
ler will return to the Main screen.
6. On the new Hand-Held (secondary) controller,
press and hold the <P/S> and then the <ENTER>
buttons to return to the LEARN MODE screen.
Youwillnoticethescreendisplaywillhavethe
following differences:
• Theletter“S”willshowatthetoprightcorner
of the screen following the version number,
indicating that it is a secondary control.
• Selections2and3arenowblank.These
options are not available on a secondary
controller.
7.PressthedownarrowbuttontodisplaytheCNTRLOPTION
screen. Notice that items 2, 3 and 5 have been changed to show
the options that a secondary remote can perform.
8. Press the <ENTER> button on both controls as necessary to return
to the Main screen.
NOTE: Any time you add something new to the network, you must
repeat this procedure to copy the new item to all secondary Hand-Held
Controllers. Otherwise, the secondary units will not know about the new
item(s).
Bekijk gratis de handleiding van Intermatic PE953, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Intermatic |
| Model | PE953 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 8177 MB |
