Intermatic PE953 handleiding
Handleiding
Je bekijkt pagina 12 van 51
12 Multi-Wave PE953 Installation Guide
Copyright © 2011 Intermatic, Inc.
Conguring for a 1-Speed or 2-Speed Pump
The default setup is for a single-speed pump, which you turn ON and
OFF using button 1 on the Hand-Held Controller.
Ifthepool/spainstallationusesatwo-speedpump,youneedto
program the Hand-Held Controller to be able to switch between
speeds.Oncecongured,theHand-HeldControllercontrolsthese
pumps as follows:
• Button <1> selects High speed.
• Button <2> selects Low speed.
1. Ifnecessary,pressandreleaseanybutton
on the Hand-Held Controller to wake it
from sleep. If the screen is not displaying
LEARN MODE, press and hold the <P/S>
and <ENTER> buttons at the same time to
put the device into programming mode.
You are in programming mode when the
LEARN MODE screen is displayed, as
shown at the right.
2. Press the DOWN arrow button until you
s e e t h e P E 6 5 3 O P T I O N s c r e e n , a s s h o w n .
3. Press and release the <1> function button
to select PUMP. The screen refreshes, as
shown.
4. Press the UP or DOWN arrow button to
change from 1SPD to 2SPD, then press
the <ENTER> button. The screen adds the
word SUCCESSFUL, then returns to the
programming screen.
5. Press the <ENTER> button again to return to the Main screen.
Calibrating Pool, Spa and Air Temperature Settings
IfthereisadiscrepancybetweentemperaturesshownontheHand-
Held Control and independent thermometers used to measure
temperatures of pool, the spa and the air, you can calibrate the Hand-
Held’ssettingstomatchtheindependentthermometers.
1. Ifnecessary,pressandreleaseanybutton
on the Hand-Held Controller to wake it
from sleep. If the screen is not displaying
LEARN MODE, press and hold the <P/S>
and <ENTER> buttons at the same time to
put the device into programming mode.
You are in programming mode when the
LEARN MODE screen is displayed, as
shown at the right.
2. Press the DOWN arrow as necessary
toviewthePE653OPTIONscreen,as
shown.
3. Press and release the <2> function button to
selectCALIBRATETEMPS.Thescreen
refreshes, as shown.
4. Using POOL as an example, press the <1>
function button to calibrate the POOL
temperature setting. The screen displays only
the POOL setting, as shown.
The AIR temperature calibration is done the
same way by pressing the <2> function
button for AIR and continuing below.
5. Press the UP or DOWN arrow button to add or
subtract degrees from the temp that will be
displayed for POOL (or SPA) temperature on
the Hand-Held screen.
NOTE: You can set the temperature offset by ±5F.
6. Press the <ENTER> button to save your changes. The screen adds the
word SUCCESSFUL, then returns to Step 5.
7. Press the <ENTER> button again as necessary to return to the Main
screen.
Conguring for a Booster (Cleaner) Pump
Ifthepool/spainstallationincludesabooster(cleaner)pump,youneedto
program the Hand-Held Controller to identify the pump and/or pump speed
that must be active for the pump to operate.
1. Ifnecessary,pressandreleaseanybuttonon
the Hand-Held Controller to wake it from
sleep. If the screen is not displaying
LEARN MODE, press and hold the <P/S> and
<ENTER> buttons at the same time to put the
device into programming mode. You are
in programming mode when the LEARN MODE
screen is displayed, as shown at the right.
2. Press the DOWN arrow button until you see the
PE653OPTIONscreen,asshown.
3. Press and release the <3> function button
to select CLEANER. The screen refreshes, as
shown.
4. Press the UP or DOWN arrow button to change
fromOFFtoCIR1(circuitorbutton1),then
press the <ENTER> button. The screen adds
the word SUCCESSFUL, then returns to the
programming screen.
NOTE: If a variable speed pump has been installed, you may select one of
the four variable speed pump speeds for this function.
5. Press the <ENTER> button again to return to the Main screen.
Bekijk gratis de handleiding van Intermatic PE953, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Intermatic |
| Model | PE953 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 8177 MB |
