Icom IC-7760 handleiding
Handleiding
Je bekijkt pagina 34 van 100
3-9
BASIC MANUAL
3
BASIC OPERATION
When not using the [RX-ANT] connector:
Set to between “ANT 1” and “ANT 4.”
L When “ANT 1/R” ~ “ANT 4/R” is selected, the signal
is switched to the [RX-ANT IN] connector, and then
reception in [ANT 1] ~ [ANT 4] is disconnected.
When an optional antenna tuner is connected:
When an optional antenna tuner
is connected to the antenna
connector set to “External Antenna
Tuner Connection,” “(EXT)” is
displayed.
Adjusting the microphone gain
1. Set the operating band and mode to SSB, AM, or
FM. (p. 3-3)
2. Push
MULTI
to open the Multi-function menu.
3. Hold down [PTT] on the microphone.
• The TX/RX indicator lights red, and is displayed.
4. Touch [MIC GAIN], and rotate
MULTI
to adjust
the microphone gain.
L Information
• Hold the microphone 5 to 10 cm (2 to 4 inches) from
your mouth, then hold down [PTT] on the microphone
and speak at your normal voice level.
• In the SSB mode, display the ALC meter, and rotate
to adjust the microphone gain until the meter reading
swings between 30 to 50% of the ALC scale.
• In the AM or FM mode, check the audio clarity with
another station, or use the Monitor function (p. 4-8).
5. Release [PTT].
• Returns to receive.
Dial Lock function
The Dial Lock function prevents frequency changes
caused by accidentally moving
MAIN
DIAL
.
L This function electronically locks the dial.
z Hold down
SPEECH
for 1 second to turn the Dial
Lock function ON or OFF.
• is displayed while the function is ON.
L You can select the Dial lock or Panel lock. (p. 8-6)
MENU
»
SET > Function > Lock Function
Hold down
SPEECH
for 1 second.
Basic transmission
1. Hold down [PTT] (or push
TRANSMIT
) to transmit.
• The TX/RX indicator lights red, and is displayed.
2. Release [PTT] (or push
TRANSMIT
again).
• Returns to receive.
Selecting the antenna connector
Set the antenna connector to between “ANT 1” and
“ANT 4,” and turn the receive antenna connector ON
or OFF.
1. Select the Main band or Sub band.
2. Select the operating band.
3. Touch [ANT] in the Multi-function key group to set
to between “ANT 1” and “ANT 4.”
L Touching [ANT] changes the antenna connector
between “ANT 1,” “ANT 2,” “ANT 3,” and “ANT 4.”
L Touch [ANT] for 1 second to set the antenna that
is connected to the selected antenna connector for
transmitting, and the antenna connected to [RX-ANT
IN] for receiving.
L “” is displayed if you temporarily select an antenna
that is dierent from the one that is saved in memory.
- Touch [ANT MW] for 1 second to save the
temporary selection into memory, then “”
disappears.
MENU
»
ANTENNA > ANT MW
L When the antenna selection mode ([ANT] SW) is
set to “Manual,” each antenna connector is selected
according to the saved settings.
MENU
»
ANTENNA > [ANT] SW
Bekijk gratis de handleiding van Icom IC-7760, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Icom |
| Model | IC-7760 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 18538 MB |
