Hughes & Kettner Switchblade 50 Combo handleiding

Niet gecategoriseerd

Hughes & Kettner

68 pagina's

PDF beschikbaar

Handleiding

Switchblade

6.1.3 TAP

The TAP function gives you a very fast and convenient option for

changing the Delay’s TIME parameter. TAP comes in particularly handy

on stage: Simply tap your foot on the TAP button in Time with the

groove to match delay Time to the tempo. The effect adopts the new

time after the second tap. The TAP LED flashes for about five seconds

in time with the beat to give you a visual indication of the delay time.

Note: The TAP function works only when the DELAY is active. If the

DELAY is off, the effect will not adopt your TAP tempo.

6.1.4 Switching External Devices via the

FSM 432, Setting the MIDI Send Channel

If you wish to switch devices connected to SWITCHBLADE MIDI THRU

– say, a MIDI effect device – using the FSM 432, ensure the effect

device is set to the FSM 432’s MIDI Channel or to OMNI. Consult the

device’s manual for more info.

To set the FSM 432’s MIDI Send Channel, proceed as follows:

• Turn SWITCHBLADE on while pressing the FSM 432’s PRESET A

button. The display flashes.

• Release button A. Use UP/DOWN to view and set the MIDI Channel

to a number between 1 and 16.

• Quit and store by pressing the PRESET A button.

Caution: If SWITCHBLADE and FSM 432 are not set to the same

MIDI channel, the amp will not respond to program changes!

Activating OMNI solves the problem in the event of an “emergency.”

See chapter 6.2 to learn more.

Note: If an external effect device is connected to MIDI THRU and

you want to switch Switchblade and the effect device simultaneously

with the same program change command, you must configure

Switchblade’s Store function and program this device accordingly.

Note: The table above should be big help if you wish to switch the

Presets of a device connected to the MIDI THRU directly via the

FSM 432. It shows the program changes sent by the bank/preset

combination. Please bear in mind that some MIDI devices switch

program 1 via program change command 0. If this is the case with

your outboard gear, simply add a 1 to each value indicated in this

table to activate the desired program.

6.2 Setting Switchblade’s MIDI

Channel and Switching OMNI ON/OFF

Press the SERIAL button longer than two seconds when SWITCHBLADE

is in normal operating mode, and the ORIGINAL VALUE LED will start

flashing. This assigns special programming functions to the amp’s LEDs

and buttons:

FX ON

Now serves as a +1/UP button for setting the MIDI Channel.

Serial

Now serves as a -1/DOWN button for setting the MIDI Channel.

Store

OMNI ON/OFF switches. If the STORE button (OMNI On) lights up,

SWITCHBLADE responds to all incoming program changes, irrespective

of the MIDI Channel over which they are sent. If the light on the button

is extinguished (OMNI OFF), it responds only to messages sent via the

defined MIDI Channel.

Bank

Preset

Programchange

Number

Bank

Preset

Programchange

Number

Bank

Preset

Programchange

Number

Bank

Preset

Programchange

Number

1 A 0 9 A 32 17 A 64 25 A 96

1 B 1 9 B 33 17 B 65 25 B 97

1 C 2 9 C 34 17 C 66 25 C 98

1 D 3 9 D 35 17 D 67 25 D 99

2 A 4 10 A 36 18 A 68 26 A 100

2 B 5 10 B 37 18 B 69 26 B 101

2 C 6 10 C 38 18 C 70 26 C 102

2 D 7 10 D 39 18 D 71 26 D 103

3 A 8 11 A 40 19 A 72 27 A 104

3 B 9 11 B 41 19 B 73 27 B 105

3 C 10 11 C 42 19 C 74 27 C 106

3 D 11 11 D 43 19 D 75 27 D 107

4 A 12 12 A 44 20 A 76 28 A 108

4 B 13 12 B 45 20 B 77 28 B 109

4 C 14 12 C 46 20 C 78 28 C 110

4 D 15 12 D 47 20 D 79 28 D 111

5 A 16 13 A 48 21 A 80 29 A 112

5 B 17 13 B 49 21 B 81 29 B 113

5 C 18 13 C 50 21 C 82 29 C 114

5 D 19 13 D 51 21 D 83 29 D 115

6 A 20 14 A 52 22 A 84 30 A 116

6 B 21 14 B 53 22 B 85 30 B 117

6 C 22 14 C 54 22 C 86 30 C 118

6 D 23 14 D 55 22 D 87 30 D 119

7 A 24 15 A 56 23 A 88 31 A 120

7 B 25 15 B 57 23 B 89 31 B 121

7 C 26 15 C 58 23 C 90 31 C 122

7 D 27 15 D 59 23 D 91 31 D 123

8 A 28 16 A 60 24 A 92 32 A 124

8 B 29 16 B 61 24 B 93 32 B 125

8 C 30 16 C 62 24 C 94 32 C 126

8 D 31 16 D 63 24 D 95 32 D 127

Bekijk gratis de handleiding van Hughes & Kettner Switchblade 50 Combo, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.