Handleiding
Je bekijkt pagina 6 van 32
6 49-5000885 Rev. 3
Remote Control Features and Settings-Heat Pump
10. Louver UP/DOWN Button
Press the LOUVER UP/DOWN button to choose the
position of the horizontal airflow louvers.
Status display of air flow
COOL/DRY:
HEAT:
NOTE:
• It is advisable not to keep the vertical louver in the
downward position for an extended period of time in
COOL or DRY mode, otherwise condensate water
may form on the louver.
• When turning the unit on, the remote control will
automatically return the louver to the previous set
swing position. When turning the unit off, the louver
will rotate to the full open position prior to closing.
11. Louver SIDE/SIDE Button (select models)
Feature is not available
12. ECO Button
For 1H09HN2DAA1, 1H12HN2DAA1,
1H18HN2DAA1 and 1H24HN2DAA1 models:
Press ECO button repeatedly to select each step.
1st Press: Level 3 Eco - Reduces some energy
consumption
is displayed on the display screen.
2nd Press: Level 2 Eco - Additional reduction in
energy consumption
is displayed on the display screen.
3rd Press: Level 1 Eco - Greatest reduction in
energy consumption
is displayed on the display screen.
Note: ECO modes will reduce the compressor
operation frequency and increase the time needed
to reach temperature set point. To exit ECO mode,
press ECO Button a fourth time.
FOR ALL OTHER MODELS:
Feature is not available.
13. Fahrenheit/Celsius Button
Press °F/°C to toggle remote and unit display
temperature between Fahrenheit and Celsius.
14. AUTO Button
Press the AUTO button. Auto mode -The heat
pump will automatically select Cool, Heat, or Fan
operation according to set temperature. When FAN is
set to AUTO the heat pump automatically adjusts the
fan speed according to room temperature.
15. VACATION Button
50°F Heating sets the system to maintain 50°F. This
is used to prevent freezing during long unoccupied
periods of time.
16. LOCK Button
Used to lock buttons and LCD display, use a pen
point or a similar object to depress this button.
17. LIGHT Button
The indoor display panel will show indoor set
temperature by default. Press this button once, it will
display the room temperature. Press this button twice
within 3 seconds, it will turn off the indoor display
panel. Press again to go back to display indoor set
temperature.
18. RESET Button
If the remote control is not functioning properly, use a
pen point or a similar object to depress this button to
reset the remote.
REMOTE CONTROL FEATURES AND SETTINGS
NOTE FOR 1H09HN2DAA, 1H12HN2DAA,1H18HN2DAA AND 1H24HN2DAA MODELS:
To achieve optimal capacity and efficiency at 5°F (-15°C) and below, it is recommended to operate indoor fan in
Turbo Mode.
NOTE FOR ALL OTHER MODELS: 7RDFKLHYHPRVWHႈFLHQWRSHUDWLRQRSHUDWHWKHLQGRRUXQLWZLWKIDQVSHHG
in Auto mode. In Cooling mode, use a set temperature of 78°F (25.5°C) or higher. In Heating mode, use a set
temperature of 73°F (22.5°C) or lower.
Bekijk gratis de handleiding van Hotpoint HW12HN2DAB, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Hotpoint |
| Model | HW12HN2DAB |
| Categorie | Airco |
| Taal | Nederlands |
| Grootte | 3662 MB |
