Handleiding
Je bekijkt pagina 6 van 24
ACCESSORIES
Only use pots and pans made from ferromagnetic material suitable for induction
hobs. Check for the
symbol (generally stamped on the bottom) to determine
whether a pot is suitable. A magnet may also be used to check whether the
cookware base is magnetic.
COOKWARE MATERIAL PROPERTIES
Recommended
cookware
Base made of stainless steel with
a sandwich design, enamelled
steel, cast iron.
Ensures optimum efficiency,
heats up quickly, and distributes
heat evenly.
Suitable cookware
Base not fully ferromagnetic
(magnet sticks only on part of the
cookware base).
Only the ferromagnetic area
heats up. As a result, may heat
up less quickly and heat may be
distributed less evenly.
Suitable cookware
Ferromagnetic base contains
areas with aluminium, or has a
recessed area in the centre.
The ferromagnetic area is smaller
than the actual cookware base
area. As a result, less power may
be delivered and cookware may
not heat suciently. Cookware
may not be detected.
Not suitable Normal thin steel, glass, clay,
copper, aluminium and other
non-ferromagnetic materials,
cookware with rubber feet.
Cookware is not detected and
will not heat up.
NOTE: All cookware must have a at base. Periodically check the base for any
sign of warping, as some cookware may undergo deformation due to high heat.
Using cookware that does not match the recommended sizes and properties
may signicantly aect cooking performance and cause unsatisfactory results.
ADAPTERS FOR POTS/PANS UNSUITABLE FOR INDUCTION
The use of adapter plates aects eciency and therefore increases the time
required to heat water or food. Make sure the ferromagnetic diameter of the
cookware base aligns with both the diameter of the adapter plate and the
diameter of the cooking zone. If these measurements don't match, eciency
and performance may be signicantly reduced. If these guidelines are not
followed, there may be a heat build-up that is not eectively transferred to the
pot or pan, potentially causing blackening of the plate and hob.
EMPTY POTS AND PANS
The hob is equipped with an internal safety system that activates the “Automatic
o” function when an over-high temperature is detected. The use of empty
pots and pans with a thin base is not recommended but, if they are used, the
temperature might rise quicker than the time needed for the “Automatic o” to
be triggered promptly, with the risk of damaging the pan or the hob surface. If
this happens, do not touch the pan or the hob surface. Wait for all components
to cool down. If any error message is displayed, call the Service Centre.
SUITABLE SIZE OF PAN/POT BASE FOR THE DIFFERENT COOKING
ZONES
To ensure that the hob works properly, use pots of a suitable base diameter for
each zone (refer to the table below). Please note that cookware manufacturers
often provide the size of the upper diameter of the cookware, rather than the
base diameter.
To ensure that the hob works as expected, always use a cooking zone with a size
matching the ferromagnetic size of the cookware base.
Centre the pan/pot correctly on the cooking zone in use. It is recommended
not to use pots larger than the size of the cooking zone.
2
1
3
4
COOKWARE USAGE BY ZONE
Zone Suitable cookware
shape
Suitable ferromagnetic
base (cm)
1 or 2 Round or Square 16 - 21
3 Round 16 - 21
4 Round 10 - 15
1+2
(Flexi Zone)
Oval or Rectangular
Short side 16 - 21
Long side 24 - 38
FIRST TIME USE
POWER MANAGEMENT
At the time of purchase, the hob is set to the maximum power. Adjust the
setting on the basis of the limits of your domestic electrical system, as explained
in the following paragraph.
NOTE: Depending on the power selected for the hob, some of the cooking
zone power levels and functions (e.g. boil or fast heating) may be automatically
limited to prevent the selected limit from being exceeded.
The table below shows the power used by each zone for each function, to help
you understand the possible usage limitations based on the chosen power
setting.
ZONE 1 or 2 1 + 2 3 4
POWER LEVEL 18 KW 2.2 2.2 2.5 1.5
BOOSTER KW 3.7 3.7 3.7 2.2
HEAT CONTROL KW 1.4 NA 1.4 NA
ASSISTED BOIL BOIL&COOK KW 3.0 NA 3.0 NA
MELTING KW NA NA NA 0.045
KEEP WARM KW NA NA NA 0.145
Examples with reference to the values in the table above:
If you set the “Power management setting” at 4 kW and activate multiple
cooking zones simultaneously, the hob will automatically adjust the power
levels not to exceed the overall power limit (e.g. 4 kW).
For example, with the “Power management setting” set at 4 kW, if you set zone
3 at “Booster” (=3.7 kW) and then try to activate zone 1 at level 18 (2.2 kW), the
overall power supplied would exceed the limit of 4 kW (3.7 + 2.2 = 5.9 kW). For
this reason, the hob will automatically adjust the power levels as follows: the
cooking zone set to “Booster” will be set at level 18 (=2.2 kW), while the second
cooking zone at level 15 (=1.6 kW, the maximum power level not to exceed
the 4 kW limitation).
Setting Menu: Changing the basic settings
Once you have connected the device to the main power supply, you can
change the default settings by entering the Setting menu within 60 seconds:
1. After connecting the hob to the main power supply, wait until all the LEDs
turn on and o consecutively.
2. Press and hold the On/O button (
to turn on the hob.
3. Press the Key-lock button (
) for at least 6 seconds to enter the Setting
menu. Ignore the key-lock activation sound that you will hear after 3 seconds
of pressing.
4. The setting type (eg."PL") will be shown on the top-left cooking zone
display, and its default (or current) value (eg."2_5") will appear on the
bottom-left cooking zone display.
5. You can select the setting type by using up (
) and down ( ) arrows of
the top-left cooking zone. You can change its value by using up (
) and
down (
) arrows of the bottom-left cooking zone. See the table below for
the setting types, default values and possible values.
6. Press the On/O button to conrm.
7. Without the conrmation, the hob will quit the Setting menu and return to
the previous values within 30 seconds.
ORDER
SETTING
TYPE
TOPLEFT
BOTTOMLEFT
DEFAULT
POSSIBLE VALUES
1
Power
Limitation
PL 7_4
2_5 kW ; 4_0 kW ;
6_0 kW ; 7_4 kW
2 Audio tone Aud On On/O
3 Demo mode dE O O/On
NOTE: once the demo mode function has been activated, it will remain ON
even if the main power supply is interrupted.
Bekijk gratis de handleiding van Hotpoint HTX6014DNF, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Hotpoint |
| Model | HTX6014DNF |
| Categorie | Fornuis |
| Taal | Nederlands |
| Grootte | 3817 MB |
