Hotone Ampero II Stomp 10th Anniversary Limited Edition handleiding

Niet gecategoriseerd

Hotone

103 pagina's

PDF beschikbaar

Handleiding

Customizing Your Ampero II Stomp

Example 3: Reamping or Tone Creation With Dry Tracks

You can route Ampero II Stomp’s USB audio outputs to effects chains for reamping.

In this example, all global settings are set to default, and several guitar/bass dry DI tracks are needed:

(1) On your Ampero II Stomp, create a new patch and use chain A only. Set input node Source to USB OUT 3/4, INPUT CH to L, and

keep other parameters as default;

(2) Add a AMP and a CAB module in AMP-CAB order;

(3) Launch a DAW and create two audio tracks. Set track 1’s input to None, output to USB Audio Output 3/4; set track 2’s input to

USB Audio Input 1, output to USB Audio Output 1/2. Then keep monitor switches off on both tracks;

(4) Still in DAW, set only track 2 can be recorded, and import a dry track (Audio Clip A) to track 1;

(5) Connect a pair of headphones to phones jack or a pair of monitor amps to output L/R jacks (balanced connection);

(6) In DAW, start playback and loop the dry track in track 1, you’ll hear the Audio Clip A with effects (depending on AMP and CAB

settings);

(7) Adjust AMP and CAB parameters;

(8) Turn off looping switch in DAW. Record on track 2 with track 1 playing simultaneously. Then you get a wet track as you’ve

heard in step (6) (7);

(9) Repeat the steps above to get different reamped tracks.

For tone creation, you only need to execute steps (1) to (7).

Controls

Use this Controls menu to set up unit mode, bank select mode, automatic cab match and external controllers.

Use UNIT MODE to switch between Patch Mode and Stomp Mode. This works same as holding footswitch 3 or mode selector in

main menu.

Use BANK SEL MODE to switch between two bank select modes in Patch Mode: Initial and Wait. This affects both built-in and

external footswitches:

•Initial: Ampero II Stomp will jump to a new patch immediately after switching a bank.

•Wait: When switching banks, the patch you’re using won’t be changed (footswitch LEDs on Ampero II Stomp will keep

flashing) until you tap a footswitch again to confirm your selection.

The AUTO CAB MATCH function will automatically help you match a cab when switching amps. Default is set to off:

•Great for patches with only one AMP and CAB module

•The cab will automatically change according to the amp model you choose

EXP/CTRL FUNC allows you to set up the working mode of EXP/CTRL jack and the functions of external footswitches. Available

seletions are EXP (expression pedal), Main Vol (Pre/Post, main volume), Single FS (single footswitch controller) and Dual FS (dual

footswitch controller), default is set to EXP.

•Switching to EXP: No more options available, for connecting expression pedal,the function is determinedbypatch settings.

•Switching to Main Vol (Pre/Post): No more options available, in this case, the expression pedal will act as a main volume

pedal: "Pre" acts like volume knob of your instrument (affects signal from INPUT jacks ONLY), and "Post" is for overall effect

output control. The range is fixed: minimum at fully heel and maximum at fully toe. Please make sure the EXP switch in your

patches are all set to ON before using this function.

•Switching to Single FS: An extra FS4 TAP option appears for selecting external footswitch function:

•Switching to Dual FS: Extra FS4 TAP and FS5 TAP options appear for selecting external footswitch function:

DESIGN INSPI R AT I O N

EXP/FX FUNC

Single FS

Fs4 TAP

Tap Tempo

EXP/FX FUNC

Main Vol(Pre)

EXP/FX FUNC

EXP

UNIT MODE BANK SEL MODE AUTO CAB MATCH

Patch Mode

Wait OFF

Bekijk gratis de handleiding van Hotone Ampero II Stomp 10th Anniversary Limited Edition, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.