Hotone Ampero II Stomp 10th Anniversary Limited Edition handleiding

Niet gecategoriseerd

Hotone

103 pagina's

PDF beschikbaar

Handleiding

Customizing Your Ampero II Stomp

Use OUTPUT SOURCE and FX SND SOURCE to select from different output signal source for output and FX loop send jacks:

•Normal: Both effect and USB audio output will be sent to the corresponding jack.

•USB Only: Only USB audio output will be sent to the corresponding jack. When Ampero II Stomp is your main USB audio

interface, if you need to monitor a track in a DAW while recording (or software monitoring), this selection is recommended. If

not, you’ll hear both unit effect output and a slightly delayed DAW monitor output.

•Dry: Both dry signal and USB audio output will be sent to the corresponding jack.

USB Audio

Use this menu to set up USB audio settings when using Ampero II Stomp as a USB audio interface.

Ampero II Stomp features a 8-in, 8-out USB audio interface with signal routings shown as below:

USB Audio Inputs Routing

Same rule as above: even number stands for left channel and odd number stands for right channel.

•Chain A outputs (after slot A6) are sent to USB Audio Input 1/2

•Chain B outputs (after slot B6) are sent to USB Audio Input 3/4; USB Audio Input 3/4 remains as long as the chain B is

activated (not shown grey; regardless of chain B output node settings)

•When chain A and B are in series, USB Audio Input 1/2 and 3/4 are the same

•FX Loop Return inputs are directly sent to USB Audio Input 5/6 regardless of patch settings

•Input L/R signals (dry signal) are directly sent to USB Audio Input 7/8 regardless of patch settings

USB Audio Outputs Routing

•USB Audio Output 1/2 (the main output) are sent to output L/R and phones jacks

•USB Audio Output 3/4 to 7/8 are reserved for sending different USB outputs depending on your settings of your computer or

DAWs

When recording, adjust the optimal REC LEVEL for each USB Audio Input 1/2 to 7/8 according to the instrument or other input

you’re using. Adjustable ranges are all from Mute~-60dB~+20dB, defaults are all set to 0dB.

Use MONITOR LEVEL to set a proper monitor level for overall USB audio outputs. Adjustable range is from Mute~-60dB~+6dB,

defaults is set to 0dB.

Use OUTPUT SOURCE and FX SND SOURCE to determine which USB audio output will be sent to the corresponding jack. In

default, the OUTPUT SOURCE is set to USB OUT 1/2, and FX SND SOURCE is set to USB OUT OFF.

Please note:

(1) When using FX Loop Send jack as a output jack, the output signal may vary from patch settings, such FX SND/FX LOOP

module parameter settings and position on effects chains, output node settings, etc.

(2) OUTPUT SOURCE option also affects phones output.

DESIGN INSPI R AT I O N

REC LEVEL(1/2) REC LEVEL(3/4) REC LEVEL(5/6)

0dB

FXSNDSOURCE

USBOUTOFF

0dB 0dB

REC LEVEL(7/8) MONITORLEVEL OUTPUTSOURCE

0dB

0dB USBOUT1/2

NO CAB MODE is for connecting to instrument amplifiers without changing saved patches. Turning this on will bypass the CAB/IR

module for Ampero II Stomp’s L/R output channels ignoring patch settings. You can apply different settings on L/R output channels

for different scenarios. Default is set to Off.

•Off: No cab mode off

•CAB Only: Only affects CAB module

•IR Only: Only affects IR module

•CAB+IR: Affects both CAB and IR modules

Bekijk gratis de handleiding van Hotone Ampero II Stomp 10th Anniversary Limited Edition, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.