HK Audio CONTOUR X CX 210LT handleiding
Handleiding
Je bekijkt pagina 5 van 32
CONTOUR X 210LT
5
The components used in connection with
the attachment or rigging of the system (e.g.
hoists, slings, lanyards) must be inspected
periodically by competent persons, taking into
account the ambient conditions, the respective
manufacturer’s specifi cations and the respective
national regulations, and before each installation
by instructed persons.
The operator must carry out a risk
assessment for the respective use of the system.
Among other things, the suitability of the
components used, the deadlines and scope of
the inspection of the work equipment and the
suitability of the personnel deployed must be
checked. With regard to the assembly and
dismantling of the systems, the need for
measures such as barriers and coordination of
the trades involved must also be determined on
a case-by-case basis. Conditions of use and
interactions with the working environment must
be taken into account.
The fl own system must be secured
against twisting and unintentional movement in
the event of wind. This is done by attaching
safety cords to the openings for attaching the
shackles.
Do not use in windy conditions with
impermissible wind speeds. The system must be
removed or lowered and secured by the time
wind force 8 or a gust wind speed of 20 m/s is
reached. Measures must be planned, coordinated
and carried out professionally.
Only slings and hoists certifi ed by their
manufacturer as conforming to 2006/42/EC
(outside the scope of 2006/42/EC of equivalent
quality in accordance with the respective national
regulations) may be used in rigging operations.
Only personnel who are trained and
qualifi ed for the respective task may be
deployed. This applies to assembly, dismantling,
operation, maintenance, troubleshooting, repair
and inspection.
To create a system consisting of several
mid/high units for rigging operation, these must
fi rst be fully connected to each other on the top
side before lifting. The system may then only be
lifted high enough for the connections to be
made on the underside. Only once the mid/high
units have been fully connected to each other can
the system be lifted further.
The connections of the individual
components of the fl ight rail are self-locking and
may only be loosened/replaced by the manufac-
turer or by a specialist company authorised by
the manufacturer.
To avoid swaying when lifting loads using
a hoist, make sure the load’s centre of gravity is
vertically below the hoist.
Suitable and su cient lighting must be provided
for assembly/dismantling, cleaning, trouble-
shooting, maintenance and repair. National
regulations must be observed in this respect.
Materials must be stored securely on a
su ciently stable surface. Tra c routes, in
particular escape and rescue routes, as well as
fi re extinguishing equipment, must always be
kept clear at the place of use.
Operating the system outdoors, including
any work carried out on the system, is prohibited
during thunderstorms. If there is a thunderstorm
on the way when used outdoors: Stop work, do
not touch any conductive parts, do not stand
under/near raised systems. If possible, go to a
safe room/area. Weather forecasts must be
continuously monitored.
Read these instructions. Keep these
instructions. Follow all warnings and instructions
marked on the product and in this manual.
• Do not place objects containing liquid on the
product – vases, glasses, bottles etc.
• Clean only with dry cloth.
• Do not remove any covers or sections of the
housing.
• Refer all servicing to qualifi ed service person-
nel. Servicing is required when the unit has
been damaged in any way, such as:
- If liquid has been spilled or objects have fallen
into the product.
- If the product does not operate normally when
the operating instructions are followed.
- If the product has been dropped or the cabinet
has been damaged.
• Do not install near heat sources such as radia-
tors, heat registers, stoves or other devices that
produce heat.
• Do not place naked fl ame sources, such as
lighted candles on the product.
• Use only with the cart, stand, tripod, bracket or
table specifi ed by the manufacturer or sold with
the product.
• When a cart is used, use caution when moving
the cart/product combination to avoid injury
from tip-over.
• Use only accessories recommended by the man-
ufacturer, this applies for all kind of accessories,
for example protective covers, transport bags,
stands, wall or ceiling mounting equipment.
In case of attaching any kind of accessories to
the product, always follow the instructions for
use, provided by the manufacturer. Never use
fi xing points on the product other than specifi ed
by the manufacturer.
• No objects should be inserted through the
housing openings.
• This device is capable of producing sound pres-
sure levels of more than 90 dB.
This could lead to permanent hearing damage!
Exposure to extremely high noise levels may
cause a permanent hearing loss.
Wear hearing protection if continuously exposed
to such high levels.
• The manufacturer only guarantees the safety,
reliability and e ciency of this product if:
- Assembly, extension, re-adjustment, modifi ca-
tions or repairs are carried out by the manufac-
turer or by persons authorized to do so.
- The unit is used in accordance with the operat-
ing instructions.
• This product is optimized for use with music
and speech signals.
Using this product with sine wave, square wave
or other kind of measuring signals at higher level
may lead to severe damage of the product.
• English • Deutsch
Bekijk gratis de handleiding van HK Audio CONTOUR X CX 210LT, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | HK Audio |
| Model | CONTOUR X CX 210LT |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 6343 MB |
