Hilti NCV 01 handleiding
Handleiding
Je bekijkt pagina 14 van 236
12 2370102
*2370102*
Compacting fresh concrete
WARNING
Risk of injury by the product if not guided correctly.
▶ Use both hands to hold the product firmly.
▶ Adopt a firm stance.
CAUTION
Trip hazard / fall hazard! Risk of injury due to use of incorrect protective-hose lengths.
▶ Use as short a protective hose as is appropriate for the task.
1. Briskly submerge the vibratory poker into the fresh concrete. Leave it there for several seconds, then slowly pull it out.
The concrete is sufficiently compacted when:
• No more bubbles rise to the surface.
• The concrete no longer subsides.
• The sound made by the vibratory poker no longer changes.
2. Submerge the vibratory poker into the concrete in all areas of the formwork.
▶ Avoid bringing the vibratory poker into contact with the reinforcement. The adherence of the concrete to the reinforcement can be lost
and the vibratory poker can be damaged.
3. Compact the concrete with particular intensity at the formworkcorners, because these are the areas with the highestdensity of reinforcement.
The result of compaction depends on the following points:
• Dwell time of the vibratory poker in the concrete.
• Consistency of the concrete.
• Density of reinforcement.
• Diameter of the vibratory poker.
When you use a small-diameter vibratory poker you have to compact for longer to achieve the same effect as you would with a
large-diameter vibratory poker.
Switching off
CAUTION
Risk of burn injuries due to hot vibratory poker! Touching the vibratory poker while it is hot can lead to burn injuries.
▶ Do not touch the vibratory poker until it has cooled down.
▶ Wear protective gloves.
▶ Run the internal vibrator only when it is immersed in fresh concrete.
1. Slowly pull the vibratory poker out of the fresh concrete by the protective hose and hold it in the air.
2. Press the on/off switch.
3. Wait until the product stops completely before you lay it down.
Care and maintenance
WARNING
Electric shock hazard! Attempting care and maintenance with the supply cord connected to a power outlet can lead to severe injury and burns.
▶ Always unplug the supply cord before carrying out care and maintenance tasks.
Care
• After each use, clean the vibratory poker and the protective hose in running water at low pressure (e.g. with a water hose).
• Carefully remove stubborn dirt from the tool. Remove concrete residues by inserting the product into a bed of gravel with the motor running.
• Do not clean with a high-pressure cleaner. Penetrating water can damage the product.
• Use only a slightly damp cloth to clean the casing. Do not use cleaning agents containing silicone as they can attack the plastic parts.
Maintenance
WARNING
Danger of electric shock! Improper repairs to electrical components may lead to serious injuries including burns.
▶ Repairs to the electrical section of the tool or appliance may be carried out only by trained electrical specialists.
• Check all visible parts and controls for signs of damage at regular intervals and make sure that they all function correctly.
• Do not operate the product if signs of damage are found or if parts malfunction. Have it repaired immediately by Hilti Service.
• After cleaning and maintenance, fit all guards or protective devices and check that they function correctly.
To help ensure safe and reliable operation, use only genuine Hilti spare parts and consumables. Spare parts, consumables and
accessories approved by Hilti for use with the product can be found at your local Hilti Store or online at: www.hilti.group.
Bekijk gratis de handleiding van Hilti NCV 01, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Hilti |
| Model | NCV 01 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 33322 MB |
