Hilti NCR 60 DC-22 handleiding
Handleiding
Je bekijkt pagina 8 van 48
4 2321725
*2321725*
Electrical safety
▶ Before use of the crimping tool, all live cables and other equipment carrying electric voltage within the area in which the user is working are to
be switched off. If this is not possible, the corresponding safety precautions for working in proximity to electrically live cables or equipment
applicable in your country must be implemented and observed.
▶ Before beginning work, check the working area for concealed electric cables or gas and water pipes. External metal parts of the product
could give you an electric shock or cause an explosion if you accidentally damage an electric cable or a gas or water pipe.
▶ Do not crimp live parts, i.e. parts carrying electric voltage. The crimping tool must be considered as being uninsulated and must therefore be
used in combination with personal protective equipment (protective gloves, protective footwear, protective clothing, etc.) of a type suitable
to provide protection for yourself and other persons in the vicinity. It is essential to ensure adequate insulation for working in the vicinity
of electrically live lines, for example by the use of solid insulating material or maintenance of an adequate air gap. Among other uses, the
crimping tool is suitable for use on electrically insulating aerial lifts or platforms.
▶ In order to use the crimping tool in the vicinity of electrically live lines, the user must:
▶ take all different potentials (voltages) into account.
▶ make sure that all chosen measures and tools are appropriate for the application.
▶ be trained for working on electrically live lines.
▶ wear fit-for-purpose personal protective equipment.
▶ wear appropriate, close-fitting clothing.
▶ remove metallic lifestyle accessories such as jewelry.
Power tool use and care
▶ After approx. 50 consecutive crimping operations, switch the power tool off and allow it to cool down for about 15 minutes. Overheating can
lead to damage to the crimping tool.
▶ Store the crimping tool in a dry place inaccessible to children and unauthorized persons.
▶ Hilti recommends having the crimping tool overhauled by Hilti Service after 15,000 crimping operations.
Careful handling and use of batteries
▶ Comply with the following safety instructions for the safe handling and use of Li-ion batteries. Failure to comply can lead to skin
irritation, severe corrosive injury, chemical burns, fire and/or explosion.
▶ Use only batteries that are in perfect working order.
▶ Treat batteries with care in order to avoid damage and prevent leakage of fluids that are extremely harmful to health!
▶ Do not under any circumstances modify or tamper with batteries!
▶ Do not disassemble, crush or incinerate batteries and do not subject them to temperatures over 80 °C (176 °F).
▶ Never use or charge a battery that has suffered an impact or been damaged in any other way. Check your batteries regularly for signs of
damage.
▶ Never use recycled or repaired batteries.
▶ Never use the battery or a battery-operated power tool as a striking tool.
▶ Never expose batteries to the direct rays of the sun, elevated temperature, sparking, or open flame. This can lead to explosions.
▶ Do not touch the battery poles with your fingers, tools, jewelry, or other electrically conductive objects. This can damage the battery and
also cause material damage and personal injury.
▶ Keep batteries away from rain, moisture and liquids. Penetrating moisture can cause short circuits, electric shock, burns, fire and explosions.
▶ Use only chargers and power tools approved for the specific battery type. Read and follow the relevant operating instructions.
▶ Do not use or store the battery in explosive environments.
▶ If the battery is too hot to touch, it may be defective. Put the battery in a place where it is clearly visible and where there is no risk of fire,
at an adequate distance from flammable materials. Allow the battery to cool down. If it is still too hot to touch after an hour, the battery is
faulty. Consult Hilti Service or read the document entitled "Instructions on safety and use for Hilti Li-ion batteries".
Observe the special guidelines applicable to the transport, storage and use of lithium-ion batteries. 8
Read the instructions on safety and use of Hilti Li-ion batteries that you can access by scanning the QR code at the end of these
operating instructions.
Description
Product overview 1
@
Crimping head
;
Piston return switch
=
Servicing and fault indicator
%
Battery release button
&
Battery status indicator
(
Battery
)
Installation opening for accessories
+
Work-area light
§
Control switch
/
Crimping/pressing ram
:
Pivoting bar
∙
Tab
Intended use
The product described is a cordless, electro-hydraulic crimping tool.
It is designed for crimping connection material made of copper (Cu) or aluminum (Al).
Before work commences, all live cables and other equipment carrying electric voltage within the area in which the user is working must
be switched off. If this is not possible, the corresponding safety precautions for working in proximity to live cables or equipment must be
implemented and observed.
Bekijk gratis de handleiding van Hilti NCR 60 DC-22, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Hilti |
| Model | NCR 60 DC-22 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 5905 MB |
