Hillvert HT-TWIN 300 handleiding
Handleiding
Je bekijkt pagina 5 van 17
08.12.2021 08.12.2021
8 9
ENEN
HT-TWIN 550
1. Turn the base of the trolley around(A) and attach the
rear axle(C) with the washers(E) and nuts(D). Place
the thrust bearing(G) between the front axle(B) and
the base, then put on the washer(U) and screw on
the nut(V). Do not tighten the nut(V) too much,
make sure that the front axle can turn.
2. Attach the handle bracket(F) to the front axle with
the screws(P), washers(S) and nuts(N).
5. Attach the front and rear barrier(L and K) to the
sides of the trolley base with the pins(M), and then
the side rails(J). The hinges must be on the outside.
3. Fix the wheels(I) on the axle ends using nuts(T) and
pins(R).
4. Turn the assembled trolley over, fasten the handle(H)
to the handle post(F) with the screw(Q), washer(T)
and nut(O).
15
16
12
14
5
D
C
E
B
V
U
G
A
N
S
F
P
T
R
I
Q
HF
T
O
L
J
K
M
M
A Trolley base 1x
B Front axle 1x
C Rear axle 1x
D M14 nut 2x
E M14 washer 2x
F Handle bracket 1x
G Thrust bearing 1x
H Handle 1x
I Wheel 4x
J Side barrier 2x
K Rear barrier 1x
L Front barrier 1x
M Pin 8x
N M10 nut 2x
O M16 nut 1x
P M10x55 screw 2x
Q M16x65 screw 1x
R Pin 4x
S M10 washer 2x
T M16 washer 5x
U M20 washer 1x
V M20 nut 1x
HT-TWIN 550
PREPARING FOR USE/ DEVICE USE
ASSEMBLING THE APPLIANCE
HT-TWIN 300
1. Put the central axle on the front hook(4), put the
hook spindle in the hole in the front bracket(7), put
the washer(13) on it and secure it with the pin(11).
Screw the front bracket(7) and rear bracket(8) to the
trolley base(1) with the screw(10), washer(12), and
nut(14). Tighten securely.
2. Place the wheels(6) on the ends of the front and
rear brackets. Install the washer(13). Insert a pin(11)
through the holes at the end of each axis and then
bend its ends.
3. Align the holes in the side panels(2) with the side
holes in the base of the trolley, then insert the B
pins(9) through them. Perform the operation on
each side of the trolley. Each panel is xed with 2
pins.
4. Insert the end of the handle(5) into the plastic
connector(16), then place the whole in the frame
forks and align the holes of both elements. Insert
the bolt(15) through the holes, t the washer(12) and
nut(14) and tighten.
17
10
13
7
8
4
13
11
6
CLEANING AND MAINTENANCE
a) Use only non-corrosive cleaners to clean the surface.
b) Store the unit in a dry, cool place, free from moisture
and direct exposure to sunlight.
c) The device must be regularly inspected to check its
technical eciency and spot any damage.
d) Use a soft, damp cloth for cleaning.
e) Periodically check tire pressure.
Bekijk gratis de handleiding van Hillvert HT-TWIN 300, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Hillvert |
| Model | HT-TWIN 300 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 6248 MB |
