Hikoki DB3DA handleiding
Handleiding
Je bekijkt pagina 10 van 24
English
10
CAUTION
○ When changing the rotational speed with the shift knob,
confirm that the tool is not moving. Changing the speed
while the motor is rotating will damage the gears.
○ When a large force is required for operation, set the
shift knob to “LOW”. If “HIGH” is set and the unit is
used, it may cause the motor to burn out or malfunction
prematurely.
*3 Tightening torque adjustment
<Auto Stop function>
When the clutch activates, the tool stops automatically.
See Table2 for the estimated range in which Auto Stop
activates.
NOTE
The clutch may not function if the remaining battery is
low, or on certain target materials.
Table2: Estimated range in which the Auto Stop function
activates
1 5 9 13 17 21 ∙∙∙ ∙∙∙ ∙∙∙ ∙∙∙ ∙∙∙
Range in which the Auto Stop function
activates
Range in which the Auto Stop function
does not activate
Table3: Tightening torque (Approx. N・m)
1 Approx. 0.4 N・m 13 Approx. 1.9 N・m
5 Approx. 0.9 N・m 17 Approx. 2.4 N・m
9 Approx. 1.4 N・m 21 Approx. 2.9 N・m
CAUTION
○ The clutch dial cannot be set between the numerals “1,
5, 9 … 21” or the dots. Do not use with the clutch dial
numeral between “21” and the black line at the middle
of the drill mark. Doing so may cause damage.
○ The tightening torque varies greatly depending on
conditions of the material being screwed into, the bit,
the screw, etc., so be sure to check the appropriate
tightening torque before beginning work.
○ Do not press on the tool body with more force than
necessary. Be careful not to pry or press with excessive
force, as doing so may damage the tool body.
○ When a hole is about to be pierced through, a large
force is being applied. Press with less force, and be
careful that the motor does not lock.
*4 Mounting and dismounting of the bit
NOTE
Use bits specified by HiKOKI.
A bit can be installed in this product by simply inserting it.
Insert the bit firmly all the way into the hexagon hole in the
socket. After inserting the bit, pull on it gently to ensure that
it does not come out. (Fig.9-a)
To remove the bit, while pulling on the guide sleeve, pull the
bit out. (Fig.9-b)
CAUTION
If the bit cannot be removed from the tool body, press
the bit in a drilled hole, jig, etc. so it does not turn, and
gently press the main switch in Reverse Rotation. Hold
the tool body firmly so that it does not back away.
*5 Switch operation
CAUTION
Before attaching the battery, check the movement of
the switch. Ensure that the switch returns to its original
position when you release your finger from it.
*6 Auto Shut Off function
When the battery capacity becomes low, the tool will
not start when the switch is pulled. At that time, the
indicator lamp lights up to indicate this. Additionally,
during use, if the battery capacity falls below a certain
level, the indicator lamp lights up and operation stops.
*7 Use as a manual screwdriver
NOTE
○ Use with 5 N・m (51 kgf・cm) or less.
○ Do not use excessive force when tightening, or when
removing rusted-in screws, etc. Doing so may cause
malfunction.
MAINTENANCE AND INSPECTION
WARNING
Be sure to turn off the switch and remove the battery
before maintenance and inspection.
1. Inspecting the tool
Since use of as dull tool will degrade efficiency and
cause possible motor malfunction, sharpen or replace
the tool as soon as abrasion is noted.
2. Inspecting the mounting screws
Regularly inspect all mounting screws and ensure that
they are properly tightened. Should any of the screws
be loose, retighten them immediately. Failure to do so
could result in serious hazard.
3. Maintenance of the motor
The motor unit winding is the very “heart” of the power
tool. Exercise due care to ensure the winding does not
become damaged and/or wet with oil or water.
4. Inspection of terminals (tool and battery)
Check to make sure that swarf and dust have not
collected on the terminals.
On occasion check prior, during and after operation.
CAUTION
Remove any swarf or dust which may have collected on
the terminals.
Failure to do so may result in malfunction.
5. Cleaning on the outside
When the power tool is stained, wipe with a soft dry
cloth or a cloth moistened with soapy water. Do not use
chloric solvents, gasoline or paint thinner, for they melt
plastics.
6. Storage
Store the power tool and battery in a place in which the
temperature is less than 40°C and out of reach of
children.
NOTE
Storing lithium-ion batteries.
Make sure the lithium-ion batteries have been fully
charged before storing them.
Prolonged storage (3 months or more) of batteries with
a low charge may result in performance deterioration,
significantly reducing battery usage time or rendering
the batteries incapable of holding a charge.
However, significantly reduced battery usage time may
be recovered by repeatedly charging and using the
batteries two to five times.
If the battery usage time is extremely short despite
repeated charging and use, consider the batteries dead
and purchase new batteries.
CAUTION
In the operation and maintenance of power tools, the
safety regulations and standards prescribed in each
country must be observed.
2024/06/26 17:15:16Stylesheet: ASIA Ver 2024.6.26
DB3DA_C99281851_407_ChT
Bekijk gratis de handleiding van Hikoki DB3DA, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Hikoki |
| Model | DB3DA |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 4904 MB |
