Handleiding
Je bekijkt pagina 21 van 56
21
EN
STEAM REGULATION
Press the steam button and set the percentage of
steam acting on the encoder knob + press for con-
firmation. You can set from 0 – 10 and the below
table will indicate the percentage:
Value Steam percentage
0 0%
1 10%
2 20%
3 30%
4 40%
5 50%
6 60%
7 70%
8 80%
9 90%
10 100%
MANUAL HUMIDIFICATION
If you press the steam button this allows introduc-
ing steam as long as it remains pressed
COOKING PROGRAMS STORAGE
To program a cooking process press the button and
acting on the encoder you can select the program
number to set. The programs that appear with
a fix number are already fitted. In case the program
number is flashing this means is a empty program
and you can start to inlet all information.
Loading a storage cooking program: If you want
to use memorized program press the cooking pro-
gram button and acting on the encoder you can
select the program number desired + press the
encoder for confirmation and oven will start oper-
ating.
Load New program: If you want to memorize new
program press the cooking program button and
acting on the encoder you must reach the first
number that is flashing + press confirmation.
Now you can start to inlet all information for the
first phase (temperature, time, steam, etc.) and you
will see the light on the led n. 1 + press the cooking
program button and you will skip to second phase
(see the led on n. 2 position). Introduce all infor-
mation for the second phase (temperature, time,
steam, etc.) + press the cooking program button
and you will skip to third phase (see the led on n.
3 position). Introduce all information for the third
phase (temperature, time, steam, etc.) + press the
cooking program button and you will skip to fourth
phase (see all 3 led lighting). Introduce all infor-
mation for the fourth phase (temperature, time,
steam, etc.) + press the cooking program button
for 5 seconds until will appear MEM (means that
program was memorized).
In case the cooking process as only 1 or 2 phase
when you finished to set the information (temper-
ature, time, steam, etc.) + press the cooking pro-
gram button for 5 seconds until will appear MEM
(means that program was memorized).
RETURN TO MANUAL COOKING MODE
To exit the program function and return to the
MANUAL cooking mode, hold the ENCODER knob
down until the word “MAN” appears on the display.
PRE-HEATING
It consists in heating the oven at a temperature
greater than 20% with respect to the temperature
set by the second program. This function is used
to compensate the loss of heat that occurs upon
opening the oven and upon the introduction of food
products there in. To activate pre-heating press the
cooking program button and acting on the encoder
go to first program number that is flashing + press
for confirmation. Now we are on first phase so
press the timer button and acting on encoder go
to “infin” (this means that the oven will run without
specific timing) + press encoder for confirmation.
Now you can introduce the other phase as indi-
cated previously and at end memorize. The oven
will start to pre-heat the cooking chamber until
reached 20% above the cooking temperature set
and after you will hear beep sound. The signal is
interrupted by opening the door (to introduce the
food products into the oven), thus the stage preset
by the program starts. The signal can be stopped
without enabling the stage or disabling preheating
simply by pressing the START/STOP button.
Bekijk gratis de handleiding van Hendi 223659, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Hendi |
| Model | 223659 |
| Categorie | Oven |
| Taal | Nederlands |
| Grootte | 5773 MB |
