Handleiding
Je bekijkt pagina 14 van 180
14
GB
• Touch the symbol (Fig.1.4)and then choose washing
program by touching the symbols “+” and “-” (corresponding
time alse will be shown on display): L1. Eco Wash (44min.);
L2. Normal Wash (1h 18min.); L3. Intensive Wash (1h 52min.);
L4. Rinse (11min.) and CP. Pump loading (2min.).
• Touch the symbol START/STOP to confirm program and touch
it again to start program - Washing time will be displayed in
countdown mode.
NOTE: Washing cycle can not be activated if chamber temper
-
ature is over 90°C. Display will show error E10 (See ==> Error
code identification).
• End of program will be noted by acoustic alarm for 10 sec
-
onds and flashing screen. Leave door open after cleaning.
• Every program, exluding CP program, can be interrupted by
touching the symbol START/STOP. In case of programs L1-
L3, if they will interrupt, program L4 (Rinse) will activate au
-
tomatically and can not be interrupted anymore.
IMPORTANT: First time or every time after changing detergent
tank use CP program to ensure correct system operating. If CP
program is repeated 2 times in a row, short rinse program will
activate automatically to remove any detergent remaining.
WARNING: DO NOT open the door during washing cycle!
Maintenance
• Check the operation of the appliance regularly to prevent se
-
rious accidents.
• If you see that the appliance is not working properly or that
there is a problem, stop using it, switch it off and contact the
supplier.
• All maintenance, installation and repair work must be car
-
ried out by specialised and authorised technicians, or recom-
mended by the manufacturer.
Transportation and Storage
• Before storage, always make sure that the appliance has
been disconnected from the power supply and completely
cooled down.
• Store the appliance in a cool, clean and dry place.
• Never place heavy objects on the appliance as this could
damage it.
• Do not move the appliance while it is under operation. Dis
-
connect the appliance from power supply when moving and
hold it at the bottom.
Troubleshooting
If the appliance does not function properly, please check the
below table for the solution. If you are still unable to solve the
problem, please contact the supplier/service provider.
Problems Possible cause Possible solution
Appliance
does not work
(control panel
totally off).
Faulty connection to
the power mains.
Check connection to
the power mains.
Lack of voltage. Restore the power
supply voltage.
Blown electronic
board protection
fuse.
Contact with technical
service.
Cooking cycle
active - appli
-
ance does not
work.
Door open. Close the door
properly.
Door sensor dam
-
aged.
Contact with technical
service.
Humidification /
steam produc
-
tion does not
work.
Faulty water con
-
nection.
Check connection to
the water mains.
Closed water valve. Open the valve.
Obstructed water
inlet filter.
Clean the filter.
Damaged water inlet
solenoid valve.
Contact with technical
service.
Door closed.
Steam escape
through the
gasket.
Gasket mounted not
properly.
Check gasket as
-
sembly.
Damaged gasket. Contact with technical
service.
Handle adjusted
incorrectly.
Contact with technical
service.
Non evenly
cooking.
One of the motor is
faulty or operates at
low speed.
Contact with technical
service.
The motors do not
reverse direction.
Contact with technical
service.
Error code identification
When anomalies occur during the operation of the appliance
that prevent the continuation of the cooking cycle or the au
-
tomatic washing cycle, the display shows alarms with an
acoustic warning. To reset the alarm touch the symbol ON/
OFF (Fig.1.11): the display highlights the “STAND-BY” mode. To
reactivate the appliance, touch the symbol again.The various
types of alarms are described below.
Error codes Possible cause Possible solution
E1 (red): Chamber
probe not detected
Interrupted connec
-
tion between probe
and electric board
Contact with
technical service
E2 (orange): Core
probe not detected
Improper plug-socket
connection of probe
Check connection
between probe and
core probe
Core probe damaged Contact with
technical service
E3 (red): Safety
thermostat ON
Maximum cham
-
ber temperature
exceeded
Contact with
technical service
E4 (red): Safety
thermal protection
of motor activated
Motor overheated Contact with
technical service
E8 (red): Display
board overheated
Temperature of
display board over
70°C
Contact with
technical service
E9 (red): Main elec
-
tronic microboard
overheated
Temperature of micro
board over 70°C
Contact with
technical service
E10 (orange):
Automatic washing
cycle can not be
activated
Chamber tempera
-
ture exceeds 90°C
Cool down the
chamber (cooling
function)
E15 (orange): Door
glass is up
Incorrect position of
the door glass
Move door glass
down
E16 (red): Door
glass is down
Incorrect position of
the door glass
Move door glass up
E18 (red): Power
supply blackout
Lack of main power
for over 1 minute
Reactivate the
cycle
E20 (red): Elec
-
tronic board not
detected
Display board does
not communicate
with electronic board
Contact with
technical service
Bekijk gratis de handleiding van Hendi 219966, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Hendi |
| Model | 219966 |
| Categorie | Oven |
| Taal | Nederlands |
| Grootte | 30937 MB |
