Helix AMPLIFY 201 X-OVER handleiding
Handleiding
Je bekijkt pagina 16 van 24
16
Hardware conguration
Congure the HELIX AMPLIFY 201 X-OVER as
follows
Caution: Carrying out the following steps will
require special tools and technical knowledge. In
order to avoid connection mistakes and / or dam-
age, ask your dealer for assistance if you have any
questions and follow all instructions in this manual
(see page 13). It is recommended that this unit will
be installed by an authorized HELIX dealer.
For better access to the connectors and control
units, we recommend to remove the amplier’s
cover panels, as shown on page 15, g. 2.
1. Adjusting input voltage range
To ensure optimal signal quality, the input
voltage range must be adjusted to the output
voltage of the connected signal source using
the gain range pushbutton (page 14, point 4)
to prevent damage to the amplier.
We recommend measuring the maximum out-
put voltage using an appropriate measuring
device or contacting your authorized HELIX
dealer.
If you are unsure, we recommend setting the
pushbutton to “High” (RCA / Cinch 1 - 6 V /
Highlevel 6 - 32 V) to avoid potential damage
to the device.
Low: Select this setting for standard applica-
tions, such as connecting:
- Audiotec Fischer DSP ampliers using
RCA cables
- Factory radios
- Aftermarket radios with an output voltage
of less than 3 V RMS
In this mode the input voltage range is 0.5
to 3 Volts for the lowlevel line input and 3 to
16 Volts for the highlevel speaker input.
High: Select this setting when connecting de-
vices from the following categories:
- Aftermarket radios with an output voltage
exceeding 3 V RMS
- Premium sound system ampliers with
an output power of more than 50 W RMS
- Stand-alone DSPs with an output voltage
exceeding 3 V RMS
The input voltage range in this mode is 1 to
6 Volts for the lowlevel line input and 6 to
32 Volts for the highlevel speaker input.
2. Connecting the pre-amplier input
The lowlevel line input (page 14, point 2) can
be connected to signal sources such as head
units, radios, DSPs and DSP ampliers using
an appropriate cable. The input sensitivity can
be optimally adapted to the signal source us-
ing the gain control (page 17, point 6).
3. Connecting the highlevel speaker inputs
The highlevel loudspeaker inputs A and B
(page 14, point 3) can be connected direct-
ly to the loudspeaker outputs of the signal
source (e.g., head units, radios, DSPs, DSP
ampliers) using appropriate cables (loud-
speaker cables with 1 mm² / AWG 18 max.).
Make sure that the polarity is correct. If one
or more connections have reversed polarity it
may aect the performance of the amplier.
The Highlevel Input is equipped with our pro-
prietary ADEP.3 circuit (Advanced Diagnostics
Error Protection 3rd generation) which en-
sures that the car radio detects the amplier
as a speaker and thus neither any function
of the radio (e.g. fader) will be deactivated
nor any error log in the CPU of the car will
be created. If this input is used, the remote
input (REM) does not need to be connected,
as the amplier will automatically turn on once
a loudspeaker signal is applied.
Attention: Solely use the supplied connec-
tion cable for connecting the highlevel inputs
(page 15, g. 1)!
4. Conguration of the automatic turn-on
( Auto-Remote)
This setting is only required when connecting
the signal source using highlevel signals.
The auto remote switch (page 14, point 11)
allows you to congure or deactivate the am-
plier’s automatic turn-on feature when using
the highlevel input. There are three available
modes:
Highlevel (default setting): The amplier au-
tomatically turns on as soon as a highlevel
signal is detected.
Signal: In this position, the amplier is
switched on and o by the actual music signal.
Select this mode if the amplier does not reli-
ably turn on in “Highlevel” position.
Remote: The automatic turn-on via the high-
Bekijk gratis de handleiding van Helix AMPLIFY 201 X-OVER, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Helix |
| Model | AMPLIFY 201 X-OVER |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 3093 MB |
