Hazet 9530-10 handleiding
Handleiding
Je bekijkt pagina 20 van 204
20
[
+49 (0) 21 91 / 7 92-0 •
^
hazet.de •
]
info@hazet.de
20
9530-10
Drilling wood (see figure P)
For maximum performance, use high-speed
steel or brad-point bits for wood drilling.
■
Begin drilling at a very low speed to
prevent the bit from slipping off the
starting point.
■
Increase speed as the drill bit bites into the
material.
■
When drilling “through” holes, secure a
block of wood behind the workpiece to
prevent ragged or splintered edges on the
back side of the workpiece
NOTICE: Bits may overheat unless reversed
and pulled out frequently to clear chips from
flutes.
Drilling metal
For maximum performance, use high-speed
steel bits for metal or steel drilling.
■
When drilling metals, use light oil on the
drill bit to keep it from overheating. The oil
will prolong the life of the bit and increase
the drilling efficiency.
■
Begin drilling at a very low speed to
prevent the bit from slipping off the
starting point.
■
Maintain a speed and a pressure that
allow cutting without overheating the bit.
Applying too much pressure will:
–
Overheat the Drill.
–
Wear the bearings.
–
Bend or burn bits.
–
Produce off-center or irregularly shaped
holes.
Driving screws (see figure Q)
Try to use standard-type screws for easy
driving and improved grip.
a. Install the correct driver bit.
b. Ensure that the torque-adjustment
ring is set to the most suitable setting.
If in doubt, start with a low setting
and gradually increase the setting as
necessary. Do not change the torque
setting when the tool is running.
c. Use the correct gear (“1” or “2”) for the
job and initially apply minimal pressure
to the variable speed trigger switch.
Increase the speed only when full control
can be maintained.
d. It is advisable to drill a pilot hole first.
This hole should be slightly longer than
the screw to be driven and just smaller
than the shank diameter of the screw. The
pilot hole will act as a guide for the screw
and will also make tightening the screw
less difficult. When screws are positioned
close to an edge of the material, a pilot
hole will also help to prevent splitting of
the wood.
e. Use a countersinking bit (sold separately)
to accommodate the screw head so that
it does not protrude from the surface.
f. Keep sufficient pressure on the drill to
prevent the bit turning out of the screw
head. The screw head can easily become
damaged, making it difficult to drive
home or remove.
g. To stop the drill/driver, release the
trigger switch and allow the tool to come
to a complete stop.
Maintenance and care
WARNING!
Remove the battery before carrying out any
work on the power tool.
Cleaning
■
Clean the power tool and grille in front
of the vent slots regularly. Frequency of
cleaning is dependent on the material and
duration of use.
■
Regularly blow out the housing interior
and motor with dry compressed air.
Spare parts and accessories
For other accessories, in particular tools
and polishing aids, see the manufacturer’s
catalogues.
Exploded drawings and spare-part lists can
be found on our homepage:
www.hazet.de
Disposal information
WARNING!
Render redundant power tools unusable:
mains operated power tool by removing
the power cord,
battery operated power tool by removing
the battery.
EU countries only
Do not throw electric power tools into
the household waste!
Bekijk gratis de handleiding van Hazet 9530-10, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Hazet |
| Model | 9530-10 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 29337 MB |
