Hazet 9513-2100 handleiding
Handleiding
Je bekijkt pagina 19 van 200
19
[
+49 (0) 21 91 / 7 92-0 •
^
hazet.de •
]
info@hazet.de
19
9513-2100
application.
Use the socket that matches the nut or bolt.
Select a proper working mode depending
on the type or size of the bolt and nut. Before
starting your job, always perform a test
operation to determine the proper fastening
time for your bolt or nut. It is advisable to
perform a trial run on a scrap material to
determine the best mode selection.
■
Set the direction preselector switch (7) to
forward setting.
■
Hold the tool firmly and place the socket
over the bolt or nut. Ensure that full length
of the bolt head or nut is fully engaged into
socket.
■
Depress the variable-speed trigger switch
(2) to turn the impact wrench on. Start
slowly, increasing the speed as the nut
or bolt runs downs. Set the nut or bolt
snugly by slowing the tool to a stop. If this
procedure is not followed, the tool will have
a tendency to torque or twist in your hand
when the nut or bolt seats.
■
Fasten the bolt or nut to the proper torque.
■
After fastening, always check the torque
with a torque wrench. If the fasteners are
too tight, reduce the impacting time.
NOTICE:
■
Hold the tool straight along the axis of the
bolt or nut.
■
Excessive fastening torque may damage
the bolt/nut or socket.
To loosen nuts and bolts
Use either mode 1, 2, 3 or “M” mode to loosen
nuts and bolts depending on the application.
When working overhead or working on car
tires, to prevent the loosened fasteners from
falling to the ground or into a tight space, it is
recommended to use the “M” mode to do this
job.
■
Set the direction preselector switch (7) to
reverse setting.
■
Hold the tool firmly and place the socket
over the bolt or nut. Ensure that full length
of the bolt head or nut is fully engaged into
socket.
■
Depress the variable-speed trigger switch
(2) to turn the impact wrench on. Once the
fastener is loose, the tool will stop running.
This tool also allows you to continue to
depress the trigger switch for removing the
nut from the long bolt, if necessary.
Maintenance and care
WARNING!
Remove the battery before carrying out any
work on the power tool.
Cleaning
■
Clean the power tool and grille in front
of the vent slots regularly. Frequency of
cleaning is dependent on the material and
duration of use.
■
Regularly blow out the housing interior and
motor with dry compressed air.
Spare parts and accessories
For other accessories, in particular tools
and polishing aids, see the manufacturer’s
catalogues.
Exploded drawings and spare-part lists can
be found on our homepage:
www.hazet.de
Disposal information
WARNING!
Render redundant power tools unusable:
battery operated power tool by removing
the battery.
EU countries only
Do not throw electric power tools into
the household waste!
In accordance with the European Directive
2012/19/EU on Waste Electrical and
Electronic Equipment and transposition into
national law used electric power tools must
be collected separately and recycled in an
environmentally friendly manner.
Raw material recovery instead of
waste disposal.
Device, accessories and packaging should
be recycled in an environmentally friendly
manner. Plastic parts are identified for
recycling according to material type.
WARNING!
Do not throw batteries into the household
waste, fire or water. Do not open used
batteries.
EU countries only:
In accordance with Directive 2006/66/EC
defective or used batteries must be recycled.
Bekijk gratis de handleiding van Hazet 9513-2100, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Hazet |
| Model | 9513-2100 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 28478 MB |
