Harman Kardon HKTS 10 handleiding

Handleiding

12345678910111213141516/ 16

Afdrukken

Je bekijkt pagina 7 van 16

SUB-TS10 SUBWOOFER AMPLIFIER PANEL CONTROLS AND CONNECTIONS

like action moves in and out in phase with

the main speakers. If the speakers were to

play out of phase, the sound waves pro-

duced by the subwoofer would be cancelled

out, reducing bass response. This phenome-

non depends in part on the relative place-

ment of the speakers in the room. In most

cases, the Phase Switch ∞ should be left

in the NORMAL position. However, it

does no harm to experiment with the

Phase Switch ∞, and you may leave it

in the position that maximizes bass

response.

§ High-Cut (Low-Pass) Filter Switch:

Placing this switch in the ON position acti-

vates circuitry that cuts out all audio input

signals above 120Hz. This allows the SUB-

TS10 to focus its power on reproducing the

low-frequency portion of the signal, avoid-

ing inefficiency and distortion. Engage this

filter when using the Speaker-Level

Inputs

¡, or when using the Line-Level

Full-Range Inputs

¢, unless your receiver

or processor processes its line-level output

using a low-pass filter. The filter has no

effect when the SUB Input £ is used.

¶ Music-Sense On/Off Switch: When

placed in the

AUTO position, and when the

Master Power Switch ⁄ is turned on, the

SUB-TS10 will automatically turn itself on or

place itself in the Standby mode, depending

on whether it is receiving an audio signal.

When this switch is placed in the ON posi-

tion, the SUB-TS10 will remain on, whether or

not it is receiving an audio signal.

• Filter Remote Control Input: This

input accepts a remote control signal from

a compatible Harman Kardon A/V receiver

that enables you to override the High-Cut

(Low-Pass) Filter Switch

§, by signal-

ing the SUB-TS10 to engage the filter even

when the switch is in the OFF position.

ª LED Indicator: This LED indicates

whether the SUB-TS10 is in the ON or

STANDBY state when used with the

Music-Sense On/Off Switch ¶ in the

AUTO position. The LED is lit Green to

indicate that the SUB-TS10 is receiving

an audio signal and is turned on, and the

LED is lit Red to indicate that no signal is

being received and the SUB-TS10 is in

Standby mode.

When the Music-Sense On/Off Switch

¶ is in the ON position, the LED will be lit

Green, whether or not an audio signal is

present.

When the

Master Power Switch ⁄ is

turned off, the LED goes dark, no matter

which position the

Music-Sense On/Off

Switch

¶ is in.

‚ Subwoofer-Level Control: Volume

can be adjusted using the

Subwoofer-

Level Control

. Turn the control clockwise

to increase the SUB-TS10’s volume, or

counterclockwise to decrease it.

⁄ Master Power Switch: Place this

switch in the “•” position to power-on the

SUB-TS10 subwoofer. The SUB-TS10 will

then be either in the Standby mode or

completely on, depending on the position

of the

Music-Sense On/Off Switch ¶.

¤ AC Power Cord: Make sure to plug

this cord into an active, unswitched electri-

cal outlet for proper operation of the SUB-

TS10. The cord should not be plugged into

the accessory outlets found on some audio

components.

6

12345678910111213141516/ 16

Bekijk gratis de handleiding van Harman Kardon HKTS 10, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.

Productinformatie

Gerelateerde producten van Harman Kardon (Speaker)

Handleiding bekijken

Harman Kardon Enchant Speaker

Speaker - handleiding

Andere merken in Speaker