Handleiding
Je bekijkt pagina 5 van 24
49-5001070 Rev. 0 5
ENGLISH
11. Sleep Button
This Sleep function automatically adjusts the set
temperature of the heat pump to provide a comfortable
sleeping environment. Sleep function is only available
in Cool, Heat and Auto mode. The unit will exit Sleep
function in the event of pressing Sleep button again,
tuning off the unit with remote controller or shutting
down the whole system from power outlet. If no other
command is chosen during Sleep function, the unit
will come back to the original set point after 8 hours of
run time. During Sleep function, the fan speed can be
adjusted to the desired comfort level. The control logics
for Sleep function will follow as below charts for different
modes:
1. Cool or Dry modes:
Sleep operation starts
Temp.
setting
In Cool, Dry mode
Rises 1>F
Rises 1>F
Decrease 1>FDecrease 1>F
Decrease 1>F
7h 8h1h 2h
>F
2. Heat mode:
Sleep operation starts
In Heat mode
>F
Temp.
setting
Rises 1>F
Decrease 2>F
Decrease 2>F
7h 8h1h 2h
12. Fahrenheit/Celcius Button
Press F/ C to toggle remote and unit display temperature
between Fahrenheit and Celsius.
13. Extra Function Button
Press the Extra Function button to view all other
operations. Press Confirm/Cancel to select and save the
chosen operation. If no button is pressed for 10 seconds,
the remote will exit Extra Function mode.
A) Refresh air - Feature not available on this series.
B) A-B selection - This will allow you to control two
separate units with a single remote control. Note: This
feature would be setup at the time of installation by the
contractor.
C) Auto mode
- The heat pump will automatically
select Cool, Heat, or Fan operation according to set
temperature. When Fan is set to Auto the heat pump
automatically adjusts the fan speed according to room
temperature.
D) Upper and Lower louver lock.
1. Upper louver lock
will lock the horizontal louver in
the top position. Commonly used during cooling.
2. Lower louver lock will lock the horizontal louver in
the lower position. Commonly used during heating.
3. To unlock the louver press Extra Function button until
either a single louver icon or oscillate icon .
Note: When the louver is locked, the position cannot be
changed with the Louver UP/DOWN button.
E) Timer ON/OFF: Sets a countdown timer until the unit
is turned ON/OFF. Temp +/Temp – button is pressed
with the length of time 0.5 hour increment/decrement
between 0-12 hours,and 1 hour increment/decrement
between 12- 24 hours.
1. When the remote is set to ON, the system will turn off
until the countdown timer ends. Then the indoor unit
will turn on and operate in mode, temperature setting
and fan speed that was displayed when timer was set.
2. When the remote is set to OFF, the system will remain
ON until the countdown timer ends.
F) 50°F Heating sets the system to maintain 50°F. This
is used to prevent freezing during long unoccupied
periods of time.
14. Confirm/Cancel Button
Saves and exits the Extra Function selection.
15. Health Button
Feature is not available
16. Lock Button
Used to lock buttons and LCD display.
17. Light Button
Turns ON and OFF the indoor display. To display only
set temperature, press Light button 10 times within
5 seconds. The indoor unit will beep 3 times when
successful. To return to ambient temperature display,
press Light 10 times within 5 seconds again. The
default display on the indoor unit displays the ambient
temperature. The set temperature will only display a
few seconds after adjusting it with the remote. The
indoor display panel will show indoor set temperature by
default. Press this button once, it will display the room
temperature. Press this button twice within 3 seconds,
it will turn off the indoor display panel. Press again to go
back to display indoor set temperature.
18. Reset Button
If the remote control is not functioning properly, use a pen
point or a similar object to depress this button to reset
the remote.
REMOTE CONTROL FEATURES AND SETTINGS
Bekijk gratis de handleiding van Haier Tempo QS07WB2BEA, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Haier |
| Model | Tempo QS07WB2BEA |
| Categorie | Airco |
| Taal | Nederlands |
| Grootte | 3436 MB |
