Growatt MOD 3-10KTL3-XA handleiding
Handleiding
Je bekijkt pagina 24 van 28
Error code
Description
Suggest
Error 413
IGBT drive fault
1.Restart inverter.
2.If error message still exists,contact manufacturer.
Error 414
EEPROM fault
1.Restart inverter.
2.If error message still exists, contact manufacturer.
Error 415
Internal power
test fail(PV Power
low)
1.Restart inverter.
2.If error message still exists,contact manufacturer.
Error 416
Over current
protected by
software
1.Restart inverter.
2.If error message still exists,contact manufacturer.
Error 417
The grid voltage
sampling is
inconsistent
1.Restart the machine;
2.If the fault information still exists,contact the
manufacturer.
Error 418
DSP and COM
firmware version
unmatch
1.Check the firmware version.
2.If error message still exists,contact manufacturer.
Error 419
Inconsistent
leakage current
sampling
1.Restart the machine.
2.If the fault information still exists,contact the
manufacturer.
Error 420
GFCI Module
damage
1.After shutdown,Check the leakage current module.
2.If the error message still exists, contact manufacturer
Error 421
CPLD is abnormal
1.Restart inverter.
2.If error message still exists,contact manufacturer.
Error 422
sampling is
inconsistent
1.Restart inverter.
2.If error message still exists,contact manufacturer.
Error 425
AFCI self-test
fault
1.Restart inverter.
2.If error message still exists, contact manufacturer.
Error 500
BMS
Communication
fault
1.Check 485 cable between SP and battery .
2.Check if battery is sleeping.
3.If error message still exists,contact manufacturer.
Error 501
BMS failure and
neither charge
and discharge is
allowe
1.Depend on BMS error code.
2.If error message still exists,contact manufacturer.
Error 502
Battery voltage
low
1.Check battery voltage.
2.If error message still exists,contact manufacturer.
Error 503
Battery Voltage
High
1.Check whether the battery volttage too high; if
battery OK, please restart the inverter; if not, please
replace battery.
2.If error message still exists,contact manufacturer.
Error code
Description
Suggest
Error 505
Battery terminals
reversed
1.Check battery terminals.
2.If error message still exists,contact manufacturer.
Error 506
Battery terminal
open (only for
lithium battery)
1.Check battery terminal.
2.If error message still exists,contact manufacturer.
Error 507
Lithium battery
Over Load Fault
1.Check whether output load over Lithium battery rate
power; If load too large, please reduce load.
2.If error message still exists, contact manufacturer.
Error 508
BUS2 Volt
Abnomal
1.Restart inverter.
2.If error message still exists, contact manufacturer.
Error 509
Bat Charge Ocp
1.Check whether the PV voltage is overconfigured.
2.If error message still exists,contact manufacturer.
Error 510
Bat DisCharge
Ocp
1.Check whether the battery discharge current is
properly set.
2.If error message still exists,contact manufacturer.
Error 511
BatSoftStartFault
1.Restart inverter.
2.If error message still exists, contact manufacturer.
Error 600
EPS OP Short
Fault
1.Restart inverter.
2.If error message still exists,contact manufacturer.
Error 601
Bus low
1.Check whether the battery works properly.
2.If error message still exists,contact manufacturer.
Error 602
AC port volt
Abnormal
1.CheckCheck whether the AC port has voltage .
2.If error message still exists,contact manufacturer.
Error 603
Soft start run out
of time
1.Restart inverter.
2.If error message still exists, contact manufacturer.
Error 604
Off-grid output
voltage is too low
1.Restart inverter.
2.If error message still exists, contact manufacturer.
Error 605
Balance Circuit
fault
1.Restart inverter.
2.If error message still exists, contact manufacturer.
Error 606
DC Voltage High
Fault
1.Restart inverter.
2.If error message still exists,contact manufacturer.
Error 607
EPS output over
load
1.Restart inverter.
2.If error message still exists,contact manufacturer.
Error 608
OfflineSignError
1.Check offline parallel signle
2.If error message still exists,contact manufacturer.
Error 609
The off-grid box
is not detected
1.Check the off-grid box after shutdown to identify the
signal wiring.
2.If error message still exists,contact manufacturer.
Error 700
Abnormal
communication
with the inverter
1.Check and communicate with the inverter after
shutdown.
2.If error message still exists,contact manufacturer.
42
41
Bekijk gratis de handleiding van Growatt MOD 3-10KTL3-XA, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Growatt |
| Model | MOD 3-10KTL3-XA |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 5306 MB |
