Handleiding
Je bekijkt pagina 22 van 37
●
●
●
Fan button
●
Mode button
●
●
AUTO COOL DRY FAN
HEAT
●
●
●
●
●
back to Auto.
NOTE
Press this button to select your required operation
mode.
Introduction for buttons on
remote controller
This button is used for setting Fan Speed in the se-
quence that goes from AUTO, , to , then
●
●
●
Medium speed
NOTE
●
●
On/Off button
Press this button to turn on the unit. Press this button
again to turn off the unit.
Having set X-FAN function on: After turning off the
Auto
Low speed
NOTE
For preventing cold air, after starting up heat mode,
indoor unit will delay 1~5 minutes to blow air (Actual
delay time depends on indoor ambient temperature).
Set temperature range from remote controller:
16~30℃(61-86℉).
This mode indicator is not available for some models.
Cooling only unit won't receive heat mode signal. If
setting heat mode with remote controller, press " On/Off "
button can't start up the unit.
It's low fan speed under dry mode.
X-FAN function Hold fan speed button for 2s in cool
This is a general use remote controller. It could be
used for the air conditioner with multifunction. For the
functions which the model doesn't have, if press the
corresponding button on the remote controller, the
unit will keep the original running status.
After putting through the power, the air conditioner
will give out a sound. Power indicator " " is ON.
After that, you can operate the air conditioner by
using remote controller.
Under on status, pressing the button on the remote
controller, the signal icon " " on the display of
remote controller will blink once and the air condition-
er will give out a "di" sound, which means the signal
has been sent to the air conditioner.
●
When selecting heat mode, the air conditioner
operates under heat mode. Press " + " or " - "
button to adjust set temperature. Press "Fan"
button to adjust fan speed. Press " "
button to adjust fan blowing angle.
mode.
This function indicates that moisture on evaporator of
indoor unit will be blowed after the unit is stopped to
avoid mould.
or dry mode, the icon " " is displayed and the in-
door fan will continue operation for a few minutes in
order to dry the indoor unit even though you have turn-
ed off the unit. After energization, X-FAN OFF is
defaulted. X-FAN is not available in auto, fan or heat
When selecting auto mode, air conditioner will
operate automatically according to the sensed
temperature. Set temperature can't be
adjusted and
will not be displayed as well. Press "Fan" button can
adjust fan speed. Press " " button can adjust
fan blowing angle.
After selecting cool mode, air conditioner will
operate under cool mode. Press " + " or " - "
button to adjust set temperature. Press "Fan"
button to adjust fan speed. Press " button "
to adjust fan blowing angle.
When selecting dry mode, the air conditioner
operates at low speed under dry mode. Under
dry mode, fan speed can't be adjusted.
Press " " button to adjust fan blowing
angle.
When selecting fan mode, the air conditioner will
only blow fan, no cooling and no heating. Press
"Fan" button to adjust fan speed. Press " "
button to adjust fan blowing angle.
- 18 -
unit by pressing " On/Off " button indoor fan will continue
running for a few minutes. at low speed. In this per-
iod, Hold fan speed button for 2s to stop indoor fan
directly.
Having set X-FAN function off: After turning off the
unit by pressing " On/Off " button, the complete unit will
be off directly.
This function is only available for some models.
Some models don't have quiet and turbo mode. The
unit operates at low fan speed when receiving the
command of quiet mode and high fan speed
when
receiving the command of turbo mode.
High speed
Bekijk gratis de handleiding van Gree GWH18PZ, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Gree |
| Model | GWH18PZ |
| Categorie | Airco |
| Taal | Nederlands |
| Grootte | 3700 MB |
