Ghibli & Wirbel S-Team 6 V handleiding
Handleiding
Je bekijkt pagina 17 van 64
17
indication to carry out cleaning as described in the
following points.
The boiler cleaning is recommended at least every 200
hours of operation or 6 months.
1- Cleaning with suction of the plastic tank (7): Check
that the water level in the plastic water tank (7) is at
least halfway up, shake/move the machine to shake the
water and any possible deposit.
Connect the flexible hose to the connector block (5) of
the machine, and hook the “TANK SUCTION”
accessory into the handle, insert the accessory tube
into the tank (7) and completely suck the water in it.
(Operation also possible in the tank (8))
2- The machine must be cold or definitely discharged
from the steam pressure and the plug disconnected.
Exhaust the contents of the boiler, carefully following
what described in the previous point "BOILER
DISCHARGE".
Prepare 2 liters of water and vinegar, in proportions of
about 60% vinegar 40% water.
Insert the prepared liquid in the refill tank of the
machine (7).
3- Turn on the machine, wait until the pump finishes
filling the boiler. (att: it may be that during the first
charge cycle, the water end indicator lights up and the
machine must be switched off / on again to complete
the load). When the pump has finished loading the
boiler and stops, immediately switch off the main
switch, unplug it and leave the machine at rest for 6-7
hours.
(Att: do not leave the solution after the indicated times).
4- With the machine cold and the plug disconnected,
shake it well and then open the cap under the boiler
(15), now empty well all the limestone dissolved in the
solution.
Now clean and close the drain plug carefully.
5- Fill the charging tank (7) with clean water. Turn the
machine on and wait for the boiler to be charged again
and following the instruction written in “Start to use”.
Wait for the charging and the heating.
Now, for about 10 minutes the steam supply will smell
of lemon given by the washing performed.
► * after the cleaning operations of the boiler, it is
advisable to check if the caps under the machine leak,
in this case check their closure with a wrench or (with
the machine discharge and cold) replace the seal with
an original spare part.
RESET service warning "-SEr": Only after cleaning the
boiler as described above, Keep the right key on the
display pressed for at least 6 seconds, until you hear a
single confirmation beep, during the acoustic beep in
the first start-up phase of the car
PROBLEMS AND SOLUTIONS
FAULT
Steam leaks from the accessories
SOLUTION (End user)
due to wear or damage of o-rings. Replace them taking
care not to damage them and insert them with attention.
Lubricate them with grease (no mineral).
FAULT
Steam tube plug is difficult to insert into the outlet of the
machine
SOLUTION (End user)
Do not force to insert it, but put a bit of silicone lubricant
on the o-rings and into the joint connection.
FAULT
The boiler needs much time to warm up.
SOLUTION (End user)
Clean the boiler as described. In case, make the
absorption with the power rating indicated in the
technical data check.
FAULT
Pressure drops quickly while using the steam
SOLUTION (End user)
Clean the boiler as described. In case, make qualified
personnel check the correct working pressure and the
integrity of the resistance.
FAULT
Intervention of the circuit breaker during use.
(Probable dispersion from the resistance or electric
valve to ground)
SOLUTION (Qualified personnel)
Check that the power cord is not visibly damaged (if so,
substitute it).
Try connecting the plug into a different socket.
Verify that there are no spills or leakage of water from
the machine that are deposited in the electrical parts.
FAULT
Steam gets out of the exhaust valve in the bottom of the
machine.
SOLUTION (Qualified personnel)
Check the correct working pressure of the boiler, check
the functioning of the level probe and in case replace
the safety valve with an original spare part, of identical
characteristics.
FAULT
Vacuum does not work (engine does not start).
(probable intervention with interruption of the fuse to
protect the socket, for excess absorption or failure of the
motor)
SOLUTION (Qualified personnel)
After checking the lack of power in the intake of the
vacuum with the vacuum control active, remove the
power plug, open the machine and replace the fuse (8A
250V Timed). Before connecting it again, check that the
motor is not shorted or has electrical problems.
DISPLAY FAULT MESSAGES:
End of water in
tank n. 7
H2O
It is necessary to fill the
tank n. 7
Boiler cleaning
warning
SEr
It is necessary to clean the
boiler as explained in point
2.
WARRANTY
Bekijk gratis de handleiding van Ghibli & Wirbel S-Team 6 V, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Ghibli & Wirbel |
| Model | S-Team 6 V |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 13555 MB |
