Genesis GLAG2045B handleiding
Handleiding
Je bekijkt pagina 9 van 30
9
ENGLISH
OPERATION
APPLICATIONS
GRINDING
WARNING: Never force the tool. The
weight of the tool applies adequate pressure. Forcing
and excessive pressure could cause dangerous wheel
breakage.
ALWAYS replace the wheel if the tool is dropped while
grinding.
NEVER bang or hit the grinding wheel or disc onto the
work.
Avoid bouncing and snagging the wheel, especially
when working on corners, sharp edges, etc. This can
case loss of control and kickback.
NEVER use the tool with wood carving blades or other
saw blades.
WARNING: After operation, always
switch off the tool and wait until the wheel comes to a
complete stop before putting the tool down.
ALWAYS select and use grinding wheels that are
recommended for the material to be ground. Ensure that
the maximum operating speed of any accessory selected
for use is not exceeded by the RPM of this tool.
ALWAYS hold the tool firmly with one hand on the motor
housing and the other on the side handle. Turn the tool on
and allow the wheel to come up to full speed, then apply
the wheel or disc to the workpiece. The key to efficient
operation begins by controlling the pressure and surface
contact between grinding wheel and the workpiece.
Flat surfaces are usually best ground by keeping the edge
of the wheel at an angle of 5° to 15°. Maintaining the proper
angle of 5° to 15° by tilting the grinder and continuously
moving the grinder back and forth or up and down over the
work area. Keep the grinder moving to avoid removing a
excessive amount of material from one area.
Use just enough pressure to keep the tool from chattering or
bouncing; normally the weight of the tool alone is adequate
for most grinding jobs. Where there is a chance that the
grinding wheel may get snagged by the workpiece, such
as loose bolts or jagged edges, causing loss of tool control,
use lighter pressure.
NOTE: It takes approximately 80 minutes to charge up
a completely discharged 2.0Ah battery pack.
BATTERY POWER INDICATOR (FIG 5)
There is a battery power indicator on the battery pack. It
has three green lights (8b). Depress the power indicator
button (8a) on the side to check the battery power level.
When all three lights illuminate, it indicates the battery is at
full power. The battery is at half full power when two lights
illuminate. When one light illuminates only, it indicates that
the battery is at a low power level and requires immediate
charging.
WARNING: Always disconnect the
battery pack from the tool or place the switch in the
locked or off position before any assembly, adjustments
or changing accessories.
SWITCH ACTION (FIG 6)
NOTE: This tool has a lock-off feature to prevent from
accidently turning on.
The switch can be locked in the "ON" position for enhanced
operator comfort during extended use. Apply caution when
locking tool in “ON” position and maintain a firm grasp on
the tool.
To Start the Tool, first press downward on the rear end of
switch , then slide the switch forward to the "ON" position.
For Continuous Operation, press the front of slide
switch downward to lock it on.
To Stop the Tool, press downward on the rear of slide
switch, the switch will return to the "OFF" position.
SAFETY SWITCH (FIG 7)
This angle grinder is equipped with a safety switch (13)
located at the bottom of the tool. It prevents the tool from
starting accidentally when inserting the battery pack, in
case the On/Off switch is locked in the "ON" position.
FIG 5
10
8a
11
8b
FIG 6
1
FIG 7
13
Bekijk gratis de handleiding van Genesis GLAG2045B, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Genesis |
| Model | GLAG2045B |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 5365 MB |
