Furman SmartSequencer CN-1800S handleiding

Niet gecategoriseerd

Furman

16 pagina's

PDF beschikbaar

Handleiding

Delay Indicators

One DELAY LED is featured for each rear outlet delay stage. Each LED

illuminates Green sequentially as each stage completes, indicating power

is available at the corresponding rear panel bank. If the CN-1800S is

operating under safe power conditions and no utility fault conditions exist,

all three Delay LEDs will remain steadily lit when all outlets ON. Once trig-

gered to power-down, each LED goes off in sequence as its correspond-

ing delay bank is deactivated. Note that the DELAY 3 output and the rear

panel DELAY 3 relay contacts are closely associated. When the indicator

DELAY 3 LED is illuminated, the DELAY 3, Common (C) and Normally

Open (NO) terminals are shorted. When the indicator DELAY 3 LED is off,

the DELAY 3, Common (C) and Normally Open (NC) terminals are shorted

DIP 1, DIP 2, and DIP 3: DIP Time Adjustment

There are three DIP switches assigned to control the time delay interval,

DIP switch positions 1, 2, & 3. The time delay, or “dwell time” between

consecutive duplexes is the same whether the CN-1800S is sequenc-

ing ON or OFF. DIP 1 adds 1 minute to the maximum time delay, DIP 2

adds 2 minutes and DIP 3 adds 4 minutes. Note: These time delays are

cumulative. If all three DIP switches are in the UP position, the maximum

allowable time delay will be 7minutes, i.e. 1min+2min+4min=7min. The

factory default setting is DIP 1 ON or UP, and DIP 2 and 3 are OFF or

DOWN. You can set these switches in any position you like to achieve

your preferred time delay.

Delay Adjustment

In order to precisely dial in your preferred sequence dwell time, it is nec-

essary to set the Time Delay Adjustment (DLY ADJ) located next to the DIP

Switch. If this potentiometer is turned to its 100% value (fully clockwise),

then the time delay will be equal to the maximum time delay deﬁned by

DIP switches 1, 2, and 3. If the potentiometer is in the 12:00 o’clock po-

sition (50%), then the time delay will be 50% of the maximum time delay

interval deﬁned by the setting of DIP Switch positions 1,2 & 3. If all three

DIP switches are off, and the potentiometer is turned completely counter-

clockwise, the time delay is miminal. The Delay Adjustment potentiometer

comes factory-set at 50%, the 12 o’clock position.

Example: If the DIP Switches are set to a 6 minute maximum delay

and the potentiometer is set to its 50% setting, then the delay interval

between sequenced banks will be 3 minutes. (DIP 1 OFF or DOWN, DIP 2

and DIP 3 ON or UP) x .50 = 6 minutes x .50 = 3 minutes.

PRIMARY LINK

SECONDARY LINK

ETHERNET

DELAY 1

DELAY 2

DELAY 3

POWER

PROTECTION OK

EXTREME VOLTAGE

UNSWITCHED

START

SEQUENCE

15 AMPS

PUSH TO RESET

OFF

REMOTE

DLY

ADJ

1 2 3 4 5 6 7 8 9

1 2 3 4 5

N.O.

N.C.

12V ON

12V OFF

GND

MOM

MNT

PRI

SEC

EVS AUTO

MANUAL

6 7 8 9

PRIMARY LINK

SECONDARY LINK

ETHERNET

DELAY 1

DELAY 2

DELAY 3

POWER

PROTECTION OK

EXTREME VOLTAGE

UNSWITCHED

START

SEQUENCE

15 AMPS

PUSH TO RESET

OFF

REMOTE

DLY

ADJ

1 2 3 4 5 6 7 8 9

1 2 3 4 5

N.O.

N.C.

12V ON

12V OFF

GND

MOM

MNT

PRI

SEC

EVS AUTO

MANUAL

6 7 8 9

Duplex 1 is powered on

Duplex 2 is powered on

Duplex 3 is powered on

Delay 3 contacts react in time with DELAY 3 Outlets

DELAY INDICATORS

DELAY 1

DELAY 2

DELAY 3

DIP Switch and Delay Adjustment

The DIP Switch is found at the center of the front panel, under the “F”

logo Security Cover. You will need to remove the cover by removing the

two M3 screws to gain access to the DIP switch. The DIP Switch is used

to set various sequencer options. It is also used in combination with the

DLY ADJ pot to set range intervals for the SWITCHED banks. The time DIP

switch settings are ON in the UP position and OFF in the DOWN position.

1 2 3 4 5 6 7 8 9

DLY

ADJ

DLY

ADJ

1 2 3 4 5

N.O.

N.C.

12V ON

12V OFF

GND

MOM

MNT

PRI

SEC

EVS AUTO

MANUAL

6 7 8 9

OFF

Factory-set DIP Settings:

DIP SWITCH DEFAULT SETTING -

Switches are factory pre-set as shown

below. Switches 1, 4, 8, and 9 are up

(ON) position.

NOTE: The DIP switch

ON / OFF settings are

indicated as shown

below throughout

this manual.

1M = 1 Minute Delay

2M = 2 Minute Delay

4M = 4 Minute Delay

NOTE: DIP 1, 2 & 3 can be summed together up to 7 minutes.

N.O. / N.C. sets Forced Off alarm poles

The out of the box factory setting is “normally open”. When sequence is “ON”.

Switched outlets will be ON until a dry contact closure is applied across the

FORCE OFF poles.

12VDC ON/OFF sets +12V pole in

Remote Mode (DIP 7 set to MNT)

Chooses +12V to REM pole functionality. In default OFF mode, a dry closed

contact across +12V to REM triggers sequencer OFF. If ON mode, closed contact

triggers ON.

• 12V OFF = Short Deactivates

• 12V ON = Short Activates

GROUND ON / OFF

Activates REM to GND pole functionality.

• REMOTE TO GROUND = ON

DIP 1

DIP 2

DIP 3

DIP 4

DIP 5

DIP 6

Bekijk gratis de handleiding van Furman SmartSequencer CN-1800S, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.